Dmr Technology; Multipoint Technology; Two-Way Radio Communication; Pairing A Bluetooth - 3M PELTOR WS LiteCom Pro III Manual

Sub channel/ Sets the subchannel of an analog
Color code (if channel according to lists (F) and (G) if
activated) it is enabled, 0 – 121. Sets the color
code of a digital channel, 0 – 15.
Output power (if This feature controls the power level of
activated) the radio transmitter. There are three
output power levels: low, medium, and
high. The low setting will reduce the
communication range but increase the
battery life.
Reset
the headset to its default state.
SMART TIP: When browsing long lists such as channel and
ten items at the time.
SMART TIP: The headset will automatically exit the menu after
exited.

Two-way radio communication

Select the appropriate two-way radio channel using the menu.
To transmit a two-way radio message, press and hold the
Push-To-Talk (PTT) button. If VOX is activated, speak into the
microphone to transmit.
SMART TIP: Your dealer can set the time for maximum
transmission time.
SMART TIP: Double press on the PTT button to activate or
deactivate VOX.
To maintain noise cancelling performance, the speech
microphone should be positioned very close to your mouth
(less than 3 mm or 1/8 inch).
Analog two-way radio
Analog two-way radio technology has the possibility to set
different frequencies for receiving and transmitting to ensure
that the headset can communicate in a repeater system.
The headset supports FM modulation and sub channels, both
CTCSS (1 – 38) and DCS (39 – 121) tones.

DMR Technology

DMR consists of three different communication modes: all call,
group call and private call. With all call you can communicate
with all DMR headsets on the same frequency and color code.
With group call you can communicate with all headsets on the
same frequency, correct color code and correct group ID. With
private call you can communicate with all headsets on the
same frequency, correct color code and correct radio ID.
This headset supports the DMR standard (tier 1 and tier 2) and
enables all call and group call. The headset also supports
digital subtones called color codes (0 – 15).
Digital two-way radio has the possibility to set different
frequencies for receiving and transmitting. This makes it
possible to communicate with a repeater system.
Bluetooth ®

Multipoint Technology

This headset supports Bluetooth
®
Bluetooth Multipoint technology to connect your headset to
two Bluetooth ® devices at the same time. Depending on the
type of Bluetooth ® devices connected and their current
activities, the headset controls the Bluetooth
different ways.The headset prioritizes and coordinates
activities from the connected Bluetooth
®

Pairing a Bluetooth

device
When the headset is powered on, press the Bluetooth
on the left cup to enter pairing mode when no device is paired.
®
Make sure that Bluetooth is activated on your Bluetooth
device. Scan for devices and
complete, "Pairing complete".
The headset can be paired to two Bluetooth
be connected to two devices at the same time.
To pair a second device using Bluetooth
press on the On/Off/Mode button to enter the menu. Use the
On/Off/Mode button to navigate through the menu, a voice will
pairing mode.
Make sure that Bluetooth ® is activated on your Bluetooth
device. Scan for devices and
complete, "Pairing complete".
NOTE: By default, the radio VOX functionality is disabled when
taking a phone call via a Bluetooth
has ended, VOX is automatically back on. To transmit on the
two-way radio during a phone call, press the PTT button. If the
PTT button is pressed during a phone call, your voice will only
transmit through the two-way radio and not to the phone call.
To activate VOX during a phone call, double press the PTT
button. Your voice will then be transmitted to both the two-way
6
EN
® Multipoint technology. Use
®
devices in
® devices.
® button
® pairing on".
®
select "WS LiteCom Pro III
® devices, and can
® pairing, make a short
®
®
select "WS LiteCom Pro III
® connection. Once the call