Related Manuals for Encore ENDSL-A
Summary of Contents for Encore ENDSL-A
- Page 1 ADSL USB Modem ADSL USB Modem User's Manual User's Manual ADSL USB Modem ADSL USB Modem...
- Page 2 Copyright Copyright 2004 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
-
Page 3: Table Of Contents
Contents 1. Introduction .................... 3 1.1 System Requirements................3 1.2 Package Contents.................. 3 2. Product Features ................... 4 2.1 ADSL Compliant ..................4 2.2 Encapsulation Mode ................4 2.3 Interface....................4 3. Hardware Indicators and Connectors ..........5 3.1 LED descriptions..................5 3.2 Front Panel .................... -
Page 4: Introduction
1. Introduction This ADSL USB Modem powered by Conexant chipset. It is featuring “always-on” function and enables high-speed broadband connection from Internet to end-users. This ADSL USB Modem ensures not only maximum performance, but also significantly simpler handling process. This ADSL USB Modem is fully compliant with ANSI T1.413 Issue 2, ITU-T G.dmt, ITU-T G.lite standards. -
Page 5: Product Features
2. Product Features 2.1 Specification ANSI T1.413 issue 2 ITU G.992.1 (G.DMT) ITU G.992.2 (G.lite) G.994.1 (G.hs, Multimode) ADSL over POTS (Annex A) or ADSL over ISDN (Annex B/UR2) Maximum downstream rate up to 8Mbps Maximum upstream rate up to 1Mbps RFC 1483 BPDU (Bridge Ethernet over ATM) RFC 1577 (Classic IP over ATM) RFC 2364 (PPP over ATM) -
Page 6: Hardware Indicators And Connectors
3. Hardware Indicators and Connectors 3.1 LED descriptions When modem is establishing the connection, the LED will be blinking. When modem is connected, the LED will be on steadily. 3.2 Front Panel Connect this connector with Type-B end of USB cable. 3.3 Rear Panel Connect this connector with RJ-11 cable. -
Page 7: Driver Installation
4. Driver Installation 4.1 Installing ADSL USB Modem The ADSL USB modem is an USB 1.1 compliant device, therefore, you need to install the USB device driver before use it. 4.1.1 For Windows 98SE and ME: When detect new hardware window appears, click “Cancel”: Insert “Easy Setup Software Kit”, front page of Easy Setup window will appear, ADSL USB Modem ADSL USB Modem... - Page 8 Install Driver: Click here to install ADSL USB modem driver. User Manual “Conexant AccessRunner USB ADSL”: Click here to read user’s manual. Acrobat: Click here to install Acrobat Reader 6.0. Panda: Click here to start Anti Virus program. Click “Install Driver”, and then select the country you are at, PS.
- Page 9 4) After finish country selecting, the window below will appear. Select the ISP, and then click “ ” to next page. 5) Enter your account “User Name, Password and Password Confirm” then click “ ” to next page, ADSL USB Modem ADSL USB Modem...
- Page 10 6) Confirm modem settings and click “ ” to next page, 7) Software kit searches available USB modem, ADSL USB Modem ADSL USB Modem...
- Page 11 After software kit find the device, operating system starts to load USB driver, For Widows 98SE, system will ask you to insert Windows 98SE installation CD, please insert the CD and click “OK” ADSL USB Modem ADSL USB Modem...
- Page 12 10) Enter correct file path and click “OK”: 11) System finishes installation and click “ ” to close installation window: ADSL USB Modem ADSL USB Modem...
- Page 13 12) If your country is not on the list, please click “ ” to next page and select “Other”, a) After you select ”other”, the window below will appear. Before you select the connection type, please refer to the following table and then select the connection type, Connection Type Encapsulation and Multiplexing method...
- Page 14 b) After finish connection type selecting, the window below will appear, and then confirm modem settings. All settings here are default, it might not correct settings for your connection, double check settings for your ISP and go to Step 13) for the detail settings.
- Page 15 13) If you want to change ISP connection settings, please go through the follow steps, Step1: Double click “AccessRunner Control Panel”: Step2: Once control panel window appears, press “Alt and C” then following window will appear. Click “Protocol Setup” then enter correct VPI, VCI and Encapsulation Mode for your ISP.
- Page 16 Step3: Connect your ISP with WAN connections, click ”AccessRunner DSL” icon, Enter correct “User name and Password” then click “Connect” to connect to your ISP: ADSL USB Modem ADSL USB Modem...
-
Page 17: For Windows 2000 And Xp
4.1.2 For Windows 2000 and XP: When detect new hardware window appears, click “Cancel”: Insert “Easy Setup Software Kit”, front page of Easy Setup window will appear, ADSL USB Modem ADSL USB Modem... - Page 18 Install Driver: Click here to install ADSL USB Modem driver. User Manual “Conexant AccessRunner USB ADSL” Click here to read user’s manual. Acrobat: Click here to install Acrobat Reader 6.0. Panda: Click here to start Anti Virus program. Click “Install Driver”, and then select the country you are at, PS.
- Page 19 4) After finish country selecting, the window below will appear. Select the ISP, and then click “ ” to next page, 5) Enter your account “User Name, Password and Password Confirm” then click “ ” to next page, ADSL USB Modem ADSL USB Modem...
- Page 20 6) Confirm modem settings and click “ ” to next page, 7) Software kit searches available USB modem, ADSL USB Modem ADSL USB Modem...
- Page 21 8) After software kit find the device, operating system start to load USB driver, 9) System finishes installation and click “ ” to close installation window, ADSL USB Modem ADSL USB Modem...
- Page 22 10) If your country is not on the list, please click “ ” to next page and select “other”, a) After you select ”other”, the window below will appear. Before you select the connection type, please check the following table and then select the connection type, Connection Type Encapsulation and Multiplexing method Network Information...
- Page 23 b) After finish connection type selection, the window below will appear, and then confirm modem settings. All settings here are default, it might not correct settings for your connection, double check settings for your ISP and go to Step 11) for the detail settings.
- Page 24 11) If you want to change ISP connection settings, please go through the follow steps, Step1: Double click AccessRunner Control Panel: Step2: Once control panel window appears, press “Alt and C” then following window will appear. Click “Protocol Setup” then enter correct VPI, VCI and Encapsulation Mode for your ISP.
- Page 25 Step3: Connect your ISP with WAN connections, click “AccessRunner DSL” icon: Enter correct “User name and Password”, and then click “Dial” to connect to your ISP, ADSL USB Modem ADSL USB Modem...
-
Page 26: Tcp/Ip Configuration
4.2 TCP / IP Configuration If your ISP provides connection service as following table, you need to follow the steps to set your IP manually. TCP/IP information: Bridged IP over ATM LLCSNAP (RFC 1483) IP address Routed IP over ATM LLCSNAP (RFC 1483) Subnet mask Bridged IP over ATM VCMUX (RFC 1483) Gateway... - Page 27 Option1: Get an IP Automatically 1) Choose Obtain an IP address automatically option in the next window 2) Select Gateway tab and click OK ADSL USB Modem ADSL USB Modem...
- Page 28 3) Select DNS Configuration tab and select Disable DNS then click OK Option2: Configure IP Manually On the IP Address field, enable specify an IP address option. Enter the IP address (e.g. 10.0.0.4) and Subnet Mask (e.g. 255.0.0.0) that provided by your ISP. ADSL USB Modem ADSL USB Modem...
- Page 29 1) Select Gateway tab and add IP Address in the New gateway field and click Add. 2) Under DNS Configuration tab, select Enable DNS and add DNS values which provided by your local ISP in DNS Server Search Order field then click Add. ADSL USB Modem ADSL USB Modem...
- Page 30 For Windows 2000 Step 1: Right click My Network Places and select Properties in the main window screen: Step 2: Right click Local Area Connection (local network your ADSL hooked up with)and select Properties: ADSL USB Modem ADSL USB Modem...
- Page 31 Step 3: Select Internet Protocol (TCP/IP) then click Properties: Configure IP Automatically: Step 4: Select Obtain an IP address automatically and Obtain DNS server address automatically then click OK to complete IP configuring process.: ADSL USB Modem ADSL USB Modem...
- Page 32 Configure IP Manually: On the IP Address field, enable specify an IP address option. Enter the IP address (e.g. 10.0.0.4), Subnet Mask (e.g. 255.0.0.0) and Default gateway (10.0.0.2) that provided by your ISP. If necessary, enter the DNS server address that provided by your ISP. For Windows XP Step 1: Click Start then select Control Panel in the main window screen: ADSL USB Modem...
- Page 33 Step 2: Double click Network Connections icon: Step 3: Right click Local Area Connection (local network your ADSL hooked up with) then select Properties: ADSL USB Modem ADSL USB Modem...
- Page 34 Step 4: Select Internet Protocol (TCP/IP) then click Properties: Configure IP address Automatically: Step 5: Select Obtain an IP address automatically and Obtain DNS server address automatically: ADSL USB Modem ADSL USB Modem...
- Page 35 Configure IP Address Manually: On the IP Address field, enable specify an IP address option. Enter the IP address (e.g. 10.0.0.4), Subnet Mask (e.g. 255.0.0.0) and Default gateway that provided by your ISP. If necessary, enter the DNS server address that provided by your ISP. If you have any troubles to configure or setup this ADSL USB Modem, please contact us.