Mitsubishi Electric MEHITS CH Technical Manual page 15

[3. Specification ]
(2) Initial setting screen
Item
Present date and time
setting
Registration of license
Unit information
(basic system)
Network setting
Advanced setting
Group setting
HW supply setting
Block setting
Energy management
Block setting
Interlocked LOSSNAY
setting
Floor layout setting
Error notification e-mail
setting
Energy-saving/peak-cut
*4 *5
control setting
Measurement setting
Temperature setting
range limit setting
Energy management
setting
Night mode schedule
setting
System changeover
setting
The present date and time can be set.
The purchased license can be registered.
Items common to main units and Web browsers of AE-200, AE-50
and EW-50.
The main unit name, identification number, expansion, date
display format, time display format, temperature display format,
pressure display format, room temperature display and availability
of illuminance sensor and motion sensor can be set.
Items only on main units of AE-200 and AE-50
The displayed language (Chinese, English, French, German,
Italian, Japanese, Portuguese, Russian, Spanish, or Turkish
can be switched, and the LCD illuminance, sound volume,
availability of test run and availability of screen lock function can
be set.
Items only on Web browsers
The display of the group name on the list screen and the display
or non-display of the filter sign can be set.
The IP addresses, subnet masks and gateways relating to the
LAN of AE-200/AE-50/EW-50 can be set, and the M-NET
addresses, range of prohibition of remote operation and external
input relating to M-NET can be set.
The time master and sub controllers can be set, the old model
compatibility mode can be turned on or off, and the season
schedule setting can be enabled or disabled.
The indoor units, LOSSNAY, general equipment, Air To Water
(PWFY) units, HWHP (CAHV, CRHV) units, Chiller units, MEHITS
CH & HP remote controllers, sub system controllers, and AHC
are registered in groups.
The HW supply units are registered in groups.
Set groups are registered in each block.
Note: A block across the AE-200, AE-50 and EW-50 systems
cannot be set.
Blocks can be set across AE-200, AE-50 and EW-50 systems.
For interlocked LOSSNAY, the indoor units are registered as
interlocking sources.
The basic floor plan, group display positions and plan view can
be set.
Note: To display plan views on the Integrated Centralized Control
Web, it is necessary to set the plan views with the Initial
Setting Tool.
Various items, such as the mail server to use the notification of
errors through e-mail and the error notification e-mail destinations,
can be set.
Note: The items must be set for each of AE-200, AE-50 and
EW-50.
The method to use the energy-saving/peak-cut control and the
method of controlling indoor and outdoor units can be set.
The conditions of the temperature and humidity sensors of AI
controller and the electricity meter and water meter of the PI
controller can be set.
When the temperature ranges to be controlled by the remote
controllers are limited, the temperature range can be set for each
remote controller.
Note: The ranges which can be monitored and controlled vary
depending on the model. This function is unusable on
P/M/S series.
The outdoor temperature measuring unit, apportionment mode
and electricity meter used as the base of apportionment can be
set.
When the night mode (low-noise operation) of outdoor units is
used, the time period in which the units will be operated in the
night mode can be set.
Note: This mode cannot be set for P/M/S sereis.
All indoor units (cooling/heating) connected to one outdoor unit
can be automatically switched according to the change in room
temperature. (Except R2 Series) The outdoor units to be
automatically switched between cooling and heating and the
switch mode (automatic/representative group) can be set.
Table Function list
Details
11
Initial
MEHITS
LCD Setting
CH & HP
Tool
)
*7
: Function provided
Initial
Integrated
setting
Web
Web