Carrier WeatherExpert 48N2 Controls, Start-Up, Operation, Service, And Troubleshooting page 204

ITEM
ALLM (cont)
ALERT LIMIT CONFIG. (cont)
DISP (cont) DISPLAY CONFIGURATION (cont)
PASS
Service Password
S.VFD SUPPLY FAN VFD CONFIG
N.VLT
VFD1 Nominal Motor Volts
N.AMP VFD1 Nominal Motor Amps
N.FRQ
VFD1 Nominal Motor Freq
N.RPM VFD1 Nominal Motor RPM
N.PWR VFD1 Nominal Motor HPwr
M.DIR VFD1 Motor Direction
ACCL VFD1 Acceleration Time
DECL VFD1 Deceleration Time
SW.FQ VFD1 Switching Frequency
E.VFD EXHAUST FAN VFD CONFIG
N.VLT VFD2 Nominal Motor Volts
N.AMP VFD2 Nominal Motor Amps
N.FRQ VFD2 Nominal Motor Freq
N.RPM VFD2 Nominal Motor RPM
N.PWR VFD2 Nominal Motor HPwr
M.DIR VFD2 Motor Direction
ACCL VFD2 Acceleration Time
DECL VFD2 Deceleration Time
SW.FQ VFD2 Switching Frequency
FLTC FILTER CONFIGURATION
FS.FT Filter Stat. Fault Timer
F.NOT
Filter Notification Cut
F.ALT Filter Alert Cutoff
MFL.S
Main Filter Status Cfg.
MF.TY Main Filter Type
MF.FR
Main Filter Final Resis.
MF.LT Main Filter Life
MF.RM
Main Filter Reminder
MF.RS Reset Main Filter Sched.
MF.ST Main Filter Status
MFT.R Reset MFT Table Entries?
PFL.S Post Filter Status Cfg.
PF.TY Post Filter Type
PF.FR Post Filter Final Resis.
PF.LT Post Filter Life
PF.RM Post Filter Reminder
PF.RS Reset Post Filter Sched.
PF.ST Post Filter Status
PFT.R Reset PFT Table Entries?
PROG PROGNOSTICS CONFIG.
LQ.SN Liquid Sensors Installed
P.SPE Prognostics SP Enable
PG.SP Prognostics SP Deadband
P.BPE Prognostics BP Enable
PG.BP Prognostics BP Deadband
AC.DB EXV Superheat Deadband
AC.SP
Auto-Comp Suct.Pres Drop
AC.DS Auto-Comp DS SP Drop
ML.DR
MLV/HGBP DP Drop
AC.CL Low Charge Alert Cutoff
AC.CH
High Charge Alert Cutoff
AC.MS Min Charge SST
AC.EC
Economizer Deadband Temp
* The display text changes depending on the remote switch configuration
(Configuration  UNIT  RM.CF). If RM.CF is set to 0 (No Remote
Switch), then the display text will be "On" or "Off." If RM.CF is set to 1
(Occupied/Unoccupied Switch), then the display text will be "Occupied"
or "Unoccupied." If RM.CF is set to 2 (Start/Stop), then the display text
will be "Stop" or "Start." If RM.CF is set to 3 (Override Switch), then the
display text will be "No Override" or "Override."
APPENDIX A — LOCAL DISPLAY TABLES (CONT)
MODE — CONFIGURATION (cont)
EXPANSION
0000 to 9999
Disable/Enable
Disable/Enable
RANGE UNITS CCN POINT
PASSWORD
0 to 999 Voltage VFD1NVLT
0 to 999 AMPS VFD1NAMP
10 to 500 VFD1NFRQ
50 to 30000 VFD1NRPM
0 to 500 VFD1NPWR
0 to 1 VFD1MDIR
0 to 1800 Seconds VFD1ACCL
0 to 1800 Seconds VFD1DECL
0 to 3 VFD1SWFQ
0 to 999 Voltage VFD2NVLT
0 to 999 AMPS VFD2NAMP
10 to 500 VFD2NFRQ
50 to 30000 VFD2NRPM
0 to 500 VFD2NPWR
0 to 1 VFD2MDIR
0 to 1800 Seconds VFD2ACCL
0 to 1800 Seconds VFD2DECL
0 to 3 VFD2SWFQ
0 to 10 Minutes
20 to 50
0 to 20
0 to 5
0 to 9
0 to 10
0 to 60
0 to 60
No/Yes
0 to 100 %
No/Yes MFTRESET
0 to 5
0 to 6
0 to 10
0 to 60
0 to 60
No/Yes
0 to 100 %
No/Yes
No/Yes
PG_SP_EN
0 to 5 "H20 PG_SP_DB
PG_BP_EN
0 to 1 "H20 PG_BP_DB
0 to 2 ^F AC_SH_DB
0 to 10 ^F AC_SP_DR
0 to 10 ^F
0 to 2 ^F AC_MLVDR
-10 to 0 ^F AC_CH_LO
0 to 10 ^F
20 to 100 ^F AC_SST_M
0 to 10 AC_EC_DB
204
DEFAULT
1111
460*
55.0*
60
1750
40*
0
30
30
2
460*
28.7*
60
1750
20*
0
30
30
2
FS_FT 2
FS_NOTIF 25
FS_ALERT 10
FLTS_ENA 0
MF_TY 0
MF_FR 1
MF_LT 12
MF_RM 10
MF_RS No
MF_STAT 0
No
PFLS_ENA 0
PF_TY 0
PF_FR 1
PF_LT 12
PF_RM 10
PF_RS No
PF_STAT 0
PFTRESET No
LQ_SENS No
Disable
0.25
Disable
0.05
2
3
AC_DS_SP 2.5
5
-3
AC_CH_HI 1
40
5.0
PAGE NO.
99
99
99
99
99
99
99
99
99
99
98,99
98,99
99
99
99
99
99
99
99
72,73
42,73
72
72
72
72
72
73
42,73
73
73
73
73
73
73
131
126
126
127
127