Advertisement
6
If necessary, use the 2 mm hex key to remove the two
screws on the back side of the mount
the connector, and replace the screws to change the
orientation of the mount.
7
Replace and tighten the screw on the handlebar connector.
NOTE: Garmin recommends tightening the screw so the
mount is secure, with a maximum torque specification of
7 lbf-in. (0.8 N-m). You should check the tightness of the
screw periodically.
8
Align the tabs on the back of the Edge device with the bike
mount notches
.
9
Press down slightly and turn the Edge device clockwise until
it locks into place.
Acquiring Satellite Signals
The device may need a clear view of the sky to acquire satellite
signals. The time and date are set automatically based on the
GPS position.
TIP: For more information about GPS, go to
/aboutGPS.
1
Go outdoors to an open area.
The front of the device should be oriented toward the sky.
2
Wait while the device locates satellites.
It may take 30–60 seconds to locate satellite signals.
Training
Going for a Ride
If your device was packaged with an ANT+
already paired and can be activated during initial setup.
1
Hold
to turn on the device.
2
Go outside, and wait while the device locates satellites.
appears solid when the device is ready.
3
From the home screen, select
4
Select the ride type.
TIP: Accurate ride type data is important for creating bike
friendly courses on your Garmin Connect account.
5
Select
to start the activity timer.
Training
, remove and rotate
www.garmin.com
®
sensor, they are
.
NOTE: History is recorded only while the activity timer is
running.
6
Select
to stop the activity timer.
7
Select an option:
• Select Resume to resume your ride.
• Select Save Ride to stop your ride and save it.
• Select Discard Ride to stop your ride and delete it from
your device.
• Select Back to Start to navigate back to your starting
location.
• Select Mark Location to mark your location and save it.
• Select Main Menu to return to the main menu.
Following a Saved Ride
1
Hold
.
2
Select Navigation > Ride an Activity.
3
Select a ride.
TIP: You can select
to view more detailed information
about your ride, such as a summary, map location, lap
details, or to delete this ride.
4
Select Ride.
5
Select
to start the activity timer.
Segments
Following a segment: You can send segments from your
Garmin Connect account to your device. After a segment is
saved to your device, you can follow the segment.
NOTE: When you download a course from your Garmin
Connect account, all segments in the course are downloaded
automatically.
Racing a segment: You can race a segment, trying to match or
exceed your personal record or other cyclists who have
ridden the segment.
Strava
™
Segments
You can download Strava segments to your Edge 130 Plus
device. Follow Strava segments to compare your performance
with your past rides, friends, and pros who have ridden the
same segment.
To sign up for a Strava membership, go to the segments widget
in your Garmin Connect account. For more information, go to
www.strava.com.
The information in this manual applies to both Garmin Connect
segments and Strava segments.
Following a Segment From Garmin Connect
Before you can download and follow a segment from Garmin
Connect, you must have a Garmin Connect account
Connect, page
10).
NOTE: If you are using Strava segments, your favorite
segments are transferred automatically to your device when it is
connected to the Garmin Connect app or your computer.
1
Select an option:
• Open the Garmin Connect app.
• Go to connect.garmin.com.
2
Create a new segment, or select an existing segment.
3
Select
or Send to Device.
4
Follow the on-screen instructions.
5
On the Edge device, select
go for a ride.
When your path crosses an enabled segment, you can race
the segment.
(Garmin
to start the activity timer, and
3
Advertisement
