Fisher & Paykel ActiveSmart E372B Installation Instructions Manual
Hide thumbs
Also See for ActiveSmart E372B:
- Installation instructions and user manual (60 pages) ,
- Installation manual (56 pages) ,
- Operating instructions manual (9 pages)
Advertisement
Quick Links
Installation instructions
Please follow the installation steps below to ensure your appliance operates correctly.
Power
• The appliance must be installed so the plug is accessible.
• To ensure that the appliance is not accidentally switched off, connect your refrigerator to its own power point. Do
not plug in any other appliance at this power point or use extension cords and double adaptors, as the combined
weight of both power cords can pull the double adaptor from a wall outlet socket.
• For power requirements, refer to the information on the serial plate located at the front bottom right-hand side of
the refrigerator when the door is open.
• It is essential that the appliance is properly grounded (earthed).
Location
• Your refrigerator should not be located in direct sunlight or next to any heat generating appliance such as a
cooktop, oven or dishwasher.
Ice & Water and Automatic Ice models
• Your Ice & Water and Automatic Ice refrigerator must be installed by an authorised plumber or Fisher & Paykel
trained and supported service technician as incorrect plumbing can lead to water leaks.
• Fisher & Paykel Appliances does not accept responsibility for damage (including water damage) caused by
faulty installation or plumbing.
Product and cabinetry dimensions
If integrating your refrigerator, please follow installation instructions provided with the integration kits.
https://producthelp.fisherpaykel.com/au/Cool/Fridges/Bottom_Freezer/Without_Ice_and_Water/790mm/RF522BRPX6/User_G...
Updated: Mon, 27 Apr 2020 00:46:14 GMT
Powered by
1
Advertisement
Related Manuals for Fisher & Paykel ActiveSmart E372B
Summary of Contents for Fisher & Paykel ActiveSmart E372B
- Page 1 Installation instructions Please follow the installation steps below to ensure your appliance operates correctly. Power • The appliance must be installed so the plug is accessible. • To ensure that the appliance is not accidentally switched off, connect your refrigerator to its own power point. Do not plug in any other appliance at this power point or use extension cords and double adaptors, as the combined weight of both power cords can pull the double adaptor from a wall outlet socket.
- Page 2 Freezer door models (E372B, RF372B, E402B, RF402B, E442B, RF442B, E522B, RF522B)(Ice & Water, Automatic Ice and non-Ice & Water models) Flush with refrigerator chassis — full door rotation Flush with refrigerator door — full door rotation https://producthelp.fisherpaykel.com/au/Cool/Fridges/Bottom_Freezer/Without_Ice_and_Water/790mm/RF522BRPX6/User_G… Updated: Mon, 27 Apr 2020 00:46:14 GMT Powered by...
- Page 3 Flush with refrigerator door — 90° door rotation Product Dimensions E402B / E442B / 522B / Property (mm) E372B / RF372B RF402B RF442B RF522B Overall height of product 1625 1725 1725 1725 Overall width of product Overall depth of product (excludes handle, includes evaporator) https://producthelp.fisherpaykel.com/au/Cool/Fridges/Bottom_Freezer/Without_Ice_and_Water/790mm/RF522BRPX6/User_G…...
- Page 4 Cabinetry Dimensions (including minimum clearances) E402B / E442B / 522B / Property (mm) E372B / RF372B RF402B RF442B RF522B Inside height of cavity 1645 1735 1735 1735 Flush with refrigerator chassis — full door rotation Inside width Inside depth Flush with refrigerator door — full door rotation Inside width Inside depth flush to door...
- Page 5 Minimum Clearances E402B / E442B / 522B / Property (mm) E372B / RF372B RF402B RF442B RF522B Side clearance Side clearance — hinge side flush with door — full rotation Side clearance — hinge side 1 with door — 90° rotation Rear clearance (incl.
-
Page 6: Installation Precautions/Warning
Connecting water (Ice & Water and Automatic Ice models) Contents of filter kit 1. 1 x 4m long x Ø6mm (1/4”) tubing 2. 1 x 200mm (8”) short Ø6mm (1/4”) tubing 3. 1 x pressure reducing valve (PRV) 4. 1 x double sided foam 5. -
Page 7: Installation Instructions
connect to potable water supply only. • DO NOT install on line pressure above 119psi (827kPa) or below 22psi (150kPa). • DO NOT use on hot water supply 38°C max. • DO NOT cut any length of tube shorter than 200mm. •... - Page 8 4. Connect the 6mm (1/4”) tubing to the outlet of the water filter cartridge as shown in Diagram 2. Gently pull to ensure it is locked. 5. Measure the required length of tubing to run from the PRV to the water connection point (no less than 250mm). 6.
- Page 9 8. Connect one locking key to each side of the water filter cartridge in between the cartridge and the locking collet as shown in Diagram 4. 9. To flush the water filter of any trapped air, harmless carbon fines and to also check for leaks, aim the end of the tubing into a bucket, turn isolating faucet on and run at least 4L of water through.
- Page 10 foam attachment 12. Run the 6mm (1/4”) tubing to the back of the refrigerator ensuring there is enough tubing to pull the refrigerator out for service. 13. Using the measurement guide shown in Diagram 6, mark out 16mm, on the end of the tubing as shown in Diagram 7.
- Page 11 • All connections must be checked for leaks. • Ensure 6mm (1/4”) tubing is routed away from sharp objects, sharp corners (beware of kinking the tube as this will stop water flow), clear of the refrigerator rear compartment and not in a location where it can be kinked or squashed.
- Page 12 There will be a 1 – 2 minute delay while the tank fills until water is dispensed. For Ice & Water and Automatic Ice models: • Turn the ice maker on by pressing the button. The light above the button will be illuminated when the ice maker is on. •...
-
Page 13: Installation (All Models)
Water dispenser (Ice & Water model only) Once installation is complete, a few drips may appear out of the dispenser over the next few days as the remaining trapped air is cleared. Installation (all models) Your Fisher & Paykel ActiveSmartTM refrigerator is fitted with front and rear rollers, designed for moving the product in the forwards and backwards direction. - Page 14 product and surrounding cabinetry. See minimum clearance in cabinetry dimensions table. C. Adjust the front feet down until the refrigerator is leaning backward with the front approximately 10mm higher than the back. This will ensure a good door closing action. (Non French door models only) D.
- Page 15 Levelling of refrigerator doors (French door models only) • For uneven surfaces, front feet can be used to align the 2 doors. • If left hand door is too low, then unscrew the left hand foot to lift up the cabinet until the two doors top edges are aligned.
- Page 16 What to do if your product is unstable A. Gently push the refrigerator back until the rear rollers contact the floor. • Measure the gap under the front foot, which has come off the floor. • Obtain some solid packing material (hardwood, plastic, etc) which fits firmly into the gap under the foot.
-
Page 17: Energy Efficiency
Before placing food in the fresh food or freezer compartments • Remove all internal packaging. Ensure that all transit clips are removed from the refrigerator. These are small rubber stoppers located at the back of the shelves. • Clean the inside of the appliance with a mix of warm water and a small amount of liquid detergent, and a soft cloth to remove manufacturing and transportation dust.