Related Manuals for D-Link DBA-1210P
Summary of Contents for D-Link DBA-1210P
- Page 1 Version 1.00 | 06/12/2016 User Manual Business Cloud Wave 2 Access Point DBA-1210P...
-
Page 2: Table Of Contents
Web-based Con guration Utility..........13 Access Point Status ............14 Access Point Local Settings..........15 Device CLI Con guration............17 Access Point Status ............17 Access Point Local Settings..........18 Mounting the Device............19 Technical Speci cations ..........22 Con guring MAC Authentication on the RADIUS Server23 D-Link DBA-1210P User Manual... -
Page 3: Package Contents
*Ceiling Bracket is an optional accessory and not included in the package. If it is required, please contact your reseller to order it. Note: Using a power supply with a di erent voltage rating or PoE injector than the one included with the DBA-1210P will cause damage and void the warranty for this product. -
Page 4: System Requirements
The following documentation provides additional information about DBA-1210P installation and management: • The Quick Installation Guide provides the information about package content and device installation. • The D-Link Business Cloud User Manual provides the guidance about device management through the D-Link Business Cloud D-Link DBA-1210P User Manual... -
Page 5: Introduction
The DBA-1210P is managed through the D-Link Business Cloud, with an intuitive browser-based interface that enables rapid deployment. Since the DBA-1210P is self-con guring and managed over the web, it can even be deployed at a remote location without on-site IT sta . -
Page 6: Features
• Streamlined Design - The DBA-1210P is designed with a slim form factor that easily blends into any o ce environment Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11b, 802.11g, 802.11n and 802.11ac speci cations. Actual data throughput will vary. -
Page 7: Hardware Overview
Section 1 - Product Overview Hardware Overview LEDs Solid Orange The DBA-1210P is connecting to the D-Link Business Cloud Cloud Solid Green The DBA-1210P is currently in Cloud mode Solid Red The DBA-1210P is not working properly in Cloud mode... -
Page 8: Bottom
LAN Port (PoE) Injector. Please see “Installation” on page <?> for more details on how to correctly power the DBA-1210P and connect to other networking devices. Press the Reset Button between 2 to 5 seconds to restart the device. Press the Reset Button between 6 to 15 seconds to restore the device to its factory Reset Button default settings. -
Page 9: Dynamic And Static Ip Addressing On The Ap
• SSH Connection to the AP Please refer to “Device CLI Con guration” on page 17 for more information on how to con gure the DBA-1210P using the CLI. Caution! If you do not have a DHCP server on your internal network, and do not plan to use one, the rst thing you must do after powering on the access point is to change the connection type from DHCP to static IP and assign a new static IP address to the AP. -
Page 10: Powering The Device
To power on the DBA-1210P, you can use one of the two following methods: 1. Connect the supplied power adapter 2. Plug one end of your Ethernet cable into the LAN port of the DBA-1210P, and the other end into a port on a Power over Ethernet enabled switch. -
Page 11: Con Gure The Device
Section 3 - Con guration Con gure the Device The easiest way to con gure the DBA-1210P is to connect the DBA-1210P to the Internet through a switch or router. Connect your computer to the Internet and manage the D-Link Business Cloud DBA-1210P via D-Link Business Cloud. - Page 12 Section 3 - Con guration 2. Connect the DBA-1210P and your computer to the same switch or router. You can then manage the access point from your computer using the following steps Enter the DBA-1210P hostname in the address eld of your...
-
Page 13: Web-Based Con Guration Utility
Section 3 - Con guration Web-based Con guration Utility This section will show you how to con gure your new D-Link Business Cloud Wave 2 Access Point using the web-based con guration utility. If you wish to change local settings for the DBA-1210P, you may use the web-based con guration utility. -
Page 14: Access Point Status
Section 3 - Con guration Access Point Status From the Status page, you can view various information about the DBA-1210P, including network status, Cloud connection status, and device information. The following table describes the elds and con guration options on the Status page. -
Page 15: Access Point Local Settings
VLAN ID is 1. Provide a number between 1 and 4094 for the management VLAN ID. Enable VLAN: To enable VLAN, select the Enable VLAN check box. To disable VLAN , clear the Enable VLAN check box. D-Link DBA-1210P User Manual... - Page 16 Click OK to con rm the upgrade and start the process. Enable Proxy: To enable proxy settings, select Enabled. To disable proxy settings, select Disabled. Host: Proxy IPv4 address or URL. Port: Proxy port number. D-Link DBA-1210P User Manual...
-
Page 17: Device Cli Con Guration
View cloud registration get system cloud-registration View date of registration get system date-of-registration View local network status get system local-network-status View internet status get system internet-status View cloud connection status get system cloud-connect-status D-Link DBA-1210P User Manual... -
Page 18: Access Point Local Settings
Set IP address or domain name of proxy server. set management proxy-host ip_address set management proxy-host domain_name Set port number of proxy server. set management proxy-port port Apply the con guration. apply Exit command line. exit Reboot the system. reboot D-Link DBA-1210P User Manual... -
Page 19: Mounting The Device
This section will show you how to con gure your new D-Link Business Cloud Wave 2 Access Point using the web-based con guration utility. To mount the DBA-1210P, use one of the following methods: Solid wall or ceiling Installation 1. Place the mounting bracket on a wall or ceiling. - Page 20 4. Use the supplied screws to attach the mounting ring to the wall. 5. Plug the Ethernet cable into the LAN port on the access point. 6. To attach the access point to the mounting bracket. D-Link DBA-1210P User Manual...
- Page 21 2. Use the provided screws to attach the mounting ring to the ceiling bracket. 3. Plug the Ethernet cable into the LAN port on the access point. 4. Place the DBA-1210P’s male bracket in the mounting bracket’s female bracket. Click DBA-1210P and the mounting racket to lock in position.
-
Page 22: Technical Speci Cations
Range will vary depending on country’s maximum transmit power output regulation. Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11b, 802.11g, 802.11n and 802.11ac speci cations. Actual data throughput will vary. Network conditions and environmental factors, including volume of network tra c, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely a ect wireless signal range. D-Link DBA-1210P User Manual... - Page 23 The station list contains client MAC address entries, and the format for the list is described in the following table. RADIUS Server Attribute Description Value User-Name MAC address of the client station. Valid Ethernet MAC Address. User-Password A xed global password used to lookup a client MAC entry. DBA-1210P D-Link DBA-1210P User Manual...
- Page 24 & & Z & Z & & & Z &...