Seiko Lorus R23 Series Instruction Manual

NREY922C
CAL. Y922 , YK30, YK31, YK32, YK33 , YK34
■ C H A R A C T E R I S T I C S
1. Time/calendar display:
second, date, day of the week and month.
2. Automatic calendar adjustment: Calendar
adjusts automatically for odd and even
months except February of leap years.
3. Time indication: Changeover between 12-
hour and 24-hour indications is possible.
4. Stopwatch: 24-hour stopwatch with 1/100
second readout up to 40 minutes and with 1
second readout after the first 40 minutes.
Split time measurement is available.
5. Alarm: The alarm rings at the designated
hour and minute with "beep, beep" for 30
seconds.
6. Hourly time signal: Can be set to ring every
hour on the hour with a single "beep".
7. Illuminating light (for Cal. YK30, YK31,
YK32, YK33, YK34 & Z001): The light evenly
illuminates the display in the dark.
■ D I S P L AY A N D B U T T O N O P E R AT I O N
H o u r l y t i m e
s i g n a l m a r k
E L b u t t o n
A
H o u r
M i n u t e
H o u r l y t i m e
s i g n a l m a r k
E L b u t t o n
A
H o u r
A M / P M i n d i c a t o r
1 2 - h o u r / 2 4 - h o u r i n d i c a t i o n
E L b u t t o n
A
H o u r
D a y
i n d i c a t o r
E L b u t t o n
A
[Cal. Y922 / Z002 / Z003]
H o u r l y t i m e
s i g n a l m a r k
A
H o u r
Button A:
• Selection of the display.
The selection is made in the following order:
T i m e / c a l e n d a r d i s p l a y
A
T i m e / c a l e n d a r s e t t i n g
Button B:
• Calendar (month, date and day) display in
the time/calendar display.
• Start/stop in the stopwatch function.
• Selection of the digits to be adjusted in the
a l a r m s e t t i n g f u n c t i o n a n d t h e t i m e /
calendar setting function.
Button C:
• Alarm display in the time/calendar display.
• Split/Split release/Reset in the stopwatch
function.
• Setting the digits in the alarm setting function
and the time/calendar setting function.
• Stopping the alarm in any display.
Button B while keeping Button C pressed:
Engagement and disengagement of the alarm
and the hourly time signal.
Button C while keeping Button B pressed:
Changeover of the calendar (month and date)
display.
Buttons B & C:
Alarm test in the time/calendar display.
■ H O W T O S E T T H E D U A L C A L E N D A R
D I S P L AY
1 Press Button B to show the calendar (month,
date, and day) display. The calendar display
is shown while Button B is kept pressed.
2 The month and the date change places with
each other with each press of Button C while
keeping Button B pressed.
D a y
M o n t h
* In the 12-hour indication, "A" (AM)/"P" (PM)
mark is displayed. In the 24-hour indication,
there is no indication.
■ H O W T O U S E T H E S T O P WAT C H
S p l i t i n d i c a t o r
S t o p w a t c h
i n d i c a t o r
A
M i n u t e
1 Press Button A to show the stopwatch display.
(The stopwatch indicator starts flashing.)
The stopwatch can measure up to 24 hours
and is displayed in minutes, seconds, and
1/100 seconds up to 40 minutes, and in
hours, minutes, and seconds after the first
40 minutes. (The 1/100 second indicator
flashes during the first 40 minutes.)
When the measurement is over 24 hours, the
stopwatch will be reset to "0:00oo" and start
counting again.
2 Reset the digits to "0:00oo" before using the
s t o p w a t c h . W h e n t h e s p l i t a n d t h e
stopwatch indicators are flashing, press
Button B to check that the stop indicator
starts flashing, and then press Button C twice
to reset the digits to zero.
3 When measuring a long period of time, return
the stopwatch to the time/calendar display
after the stopwatch starts to prevent any
possible mistaken operation.
* W h e n B u t t o n B o r C i s p r e s s e d i n t h e
stopwatch display, a single "beep" sounds
to confirm the operation.
Accumulated elapsed time measurement
B B
S t a r t S t o p
❈ Restart and stop of stopwatch can be repeated
by pressing button B.
Split time measurement
B C
S p l i t
S t a r t
❈ Measurement and release of split time can be
repeated by pressing button C.
M e a s u r e m e n t b e t w e e n t w o c o m p e t i t o r s
B C
S t a r t Finish time
of 1st
competitor
■ H O W T O S E T T H E A L A R M
A l a r m s e t i n d i c a t o r
A
H o u r
1 Press Button A for 2 seconds to activate the
alarm setting function.
indicator starts flashing.)
2 Press Button B to activate the "Hour" or
"Minute" setting. The display changes in the
following order with each press of Button B.
H o u r s e t t i n g
3 One digit (flashing) is advanced with each
press of Button C. The digits are advanced
quickly by keeping Button C pressed.
4 After all the adjustments are completed,
press Button A to return to the time/calendar
display.
(The display returns directly to the time/
calendar display and not to the time/
calendar setting.)
Note: When setting the hour digits, be sure to
check that the "A" (AM)/"P" (PM) mark is
correctly set.
Page 1
CAL. Z001, Z002 , Z003 (R23 SERIES )
[Cal. YK32 / Z001]
D a y i n d i c a t o r
E L b u t t o n
[Cal. YK30 / YK31]
D a y i n d i c a t o r
M i n u t e
[Cal. YK33]
A l a r m /
H o u r l y t i m e s i g n a l m a r k
M i n u t e
[Cal. YK34]
A M / P M i n d i c a t o r
H o u r
M i n u t e
D a y i n d i c a t o r
M i n u t e
S t o p w a t c h d i s p l a y
A
A
A
D a t e
D a t e
B
C
S t o p i n d i c a t o r
1 / 1 0 0 s e c o n d
S e c o n d
B
R e s t a r t
C
S p l i t
R e l e a s e
F i n i s h ( F i r s t r u n n e r )
F i n i s h ( S e c o n d r u n n e r )
B
Stop
M i n u t e
B
10-2010
Hour, minute,
A l a r m m a r k
B
C
S e c o n d
A l a r m m a r k
B
C
S e c o n d
D a y i n d i c a t o r
B
C
S e c o n d
A l a r m / H o u r l y t i m e
s i g n a l m a r k
B
C
S e c o n d
A l a r m m a r k
B
C
S e c o n d
P r e s s
B u t t o n A
f o r 2 s e c .
A l a r m s e t t i n g
D a y
M o n t h
1 / 1 0 0 s e c o n d
i n d i c a t o r
B : S t a r t / S t o p
C : S p l i t /
Split release/
Reset
B
❈
Stop
B
❈
S t o p R e s e t
C
R e s e t
Finish time
of 2nd
competitor
B
C
" A " ( A M )
(The alarm set
M i n u t e s e t t i n g
B
C
C
Reset
C
C
10.8.18, 5:19 PM
Adobe