In Case Of Difficulty - Kenwood CD Series Instruction Manual

In case of difficulty

What appears to be a malfunction may not alw ays be serious. If your unit should not perform as expected, consult the table
below to see if the problem can be corrected before seeking help from your dealer or service representative.
Operation to reset
The microcomputer may malfunction (impossibility to operate,
erroneous display, etc.) w hen the connection cords are un-
plugged w hile the unit is ON or due to an external factor. In this
case, execute the follow ing method to reset the microcomputer
and return it to normal condition.
CD player unit
Symptom
The unit is not turned ON w ith the ON/
STANDBY (POWER/
There is no sound even w hen a disc is loaded.
M usic is interrupted. (Sound is skipped.)
Play begins as soon as the unit is turned ON.
Remote control unit
Symptom
Remote control operation is not possible.
For the U.S.A.
CAUTION:
Use of controls or adjustment or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
In compliance w ith Federal Regulations, follow ing are reproductions of
labels on, or inside the product relating to laser product safety.
Downloaded from: http://www.usersmanualguide.com/
÷ Pow er plug is loosely connected.
) sw itch ON. ÷ With the pow er plug connected to the sw itched
AC outlet of an amplifier, the pow er of the
amplifier is turned off.
÷ Disc is loaded upside dow n.
÷ Disc is loose.
÷ Disc is dirty.
÷ Disc is cracked.
÷ Condensation has occurred on the optical lens
unit.
÷ Play mode is not entered.
÷ The connection cords are inserted loosely.
÷ Output level is attenuated too low .
÷ Disc is too dirty.
÷ Disc is cracked.
÷ Oscillation is applied to this unit.
÷ This unit is designed so that play begins auto-
matically w hen the unit is turned ON if a disc is
already loaded.
÷ Batteries are exhausted.
÷ The remote control unit is too far aw ay from the
main system, controlling angle is too large, or
there is an obstacle in betw een.
Unplug the pow er cord from the pow er socket and plug the
pow er cord into the socket again.
÷ Please be aw are that resetting the CD player w ill erase all stored
information and return it to the factory settings.
Cause
÷ Insert the pow er plug firmly to the AC outlet.
÷ Turn the amplifier's pow er ON.
÷ Load the disc again w ith its label side up.
÷ Insert disc properly.
÷ Wipe off the dust on the surface of the disc
÷ Replace the disc w ith a new one.
÷ Remove any condensation from the unit by
÷ Press the 6 key.
÷ Connect all connection cords firmly.
÷ Adjust the output level w ith OUTPUT key on
÷ Wipe off the dust on the disc surface referring
÷ Replace the disc w ith a new one.
÷ Try selecting a place w here no strong vibrations
÷ If automatic play is not required remove the
Cause
÷ Replace w ith new batteries.
÷ Operate the remote control unit w ithin the
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO, HACHIOJI-SHI,
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPM ENT
CONFORM S TO DHHS REGULATIONS NO. 21
CFR 1040.10, CHAPTER
Location: Back Panel
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
Remedy
referring to " Disc handling precautions" .
referring to the section entitled, " Caution on
condensation" .
the remote control unit.
to " Disc handling precautions" .
occur by changing the installation place, etc.
disc from the player before setting the unit to
STANDBY mode.
Remedy
controllable range.
I
, SUBCHAPTER J.
25
¢
¢
5
¢
8
8