Ryobi ONE+ P2807 Operator's Manual page 10

GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, penetrating
oils, etc., come in contact with plastic parts. Chemicals
can damage, weaken, or destroy plastic which may result
in serious personal injury.
CLEANING THE UNIT
WARNING:
Always store and dispose of chemicals properly. Disposal
of contaminated rinse water should be performed accord-
ing to local ordinances and bylaws.
Draining the tank:
If there is any liquid left in the tank after spraying, the tank
should be drained before cleaning.
 Turn off the electrostatic function and remove the battery
from the unit.
 Remove the tank and unscrew the cap.
 Drain the contents of the tank through the fill area.
NOTE: Drain the contents back into the original container.
Do not store chemicals in the tank.
Cleaning the tank and spray lines:
 Fill the tank about one-third full with clean water. A small
amount of mild household detergent may be added.
NOTE: Never use flammable chemicals or abrasive
cleaning agents to clean the tank.
 Wipe the outside of the tank with a clean, dry cloth.
 Replace the cap.
 Reinstall the tank and latch to secure.
 Reinstall the battery pack. Spray until the tank has been
emptied. Make sure to direct the spray toward an area
that will not be damaged by the spray solution.
 Refill and repeat the procedure with clean water. It may
be necessary to rinse the tank more than once, then drain
again as directed above.
 Allow all pieces to completely dry before reinstalling parts
and storing the unit.
NOTE: Store the sprayer in an upright position. DO NOT
store the sprayer on its side.
MAINTENANCE
Cleaning the sprayer:
 Fill the tank about one-third full with clean water.
 Review chemical SDS sheet how best to secure and store
 Replace the tank cap and tighten securely.
 Reinstall the battery pack. Spray until the tank has been
 Refill and repeat the procedure with clean water. It may
 Allow all pieces to completely dry, then reinstall the tank
 Wipe the outside of the sprayer with a clean, dry cloth.
INSTALLING/REMOVING THE NOZZLES
See Figures 11 - 14.
 Release the trigger and stop spraying before rotating the
 Turn off the electrostatic function and remove the battery
 Allow the unit to rest for approximately 5 minutes before
To remove the nozzle selector:
 Rotate the nozzle selector to disassembly position as
 Remove the nozzle selector from the slot in the top of the
To remove the nozzles:
 After removing the nozzle selector, unscrew the ring on
 Remove the retention plate.
 Remove nozzles and o-rings from the nozzle selector.
To install the nozzles:
 Insert the nozzles and o-rings into the main body of the
 Replace the retention plate onto the nozzle selector.
 Replace the ring on the front of the selector by rotating
To reinstall the nozzle selector:
Insert the nozzle selector in the slot at the top of the unit.
 Insert the nozzle tool into the slots of the threaded ring.
 Rotate the nozzle selector to the desired nozzle position.
10 — English
NOTE: Never use flammable chemicals or abrasive
cleaning agents to clean the tank.
your chemical solution when not in use.
emptied. Make sure to direct the spray toward an area
that will not be damaged by the spray solution.
be necessary to rinse the tank more than once, then drain
again as directed above.
cap.
nozzle selector.
from the unit.
attempting to disassemble the nozzle selector to allow
the electrostatic charge to disperse.
shown.
unit.
the front of the selector using the nozzle tool.
nozzle selector.
clockwise to tighten. Use the nozzle tool to ensure the
assembly is tight to prevent leaks.