Table of Contents
Advertisement
Quick Links
Infant to Toddler
High Chair
Product features and decorations may vary from the photo above.
Model Numbers: 79666, B2109, B2110, B2111
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tools needed for assembly: Phillips Screwdriver (not included).
Advertisement
Table of Contents
Related Manuals for Fisher-Price 79666
Summary of Contents for Fisher-Price 79666
- Page 1 Infant to Toddler High Chair Product features and decorations may vary from the photo above. Model Numbers: 79666, B2109, B2110, B2111 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Tools needed for assembly: Phillips Screwdriver (not included).
-
Page 2: Consumer Information
Usually, we can solve the problem over the telephone or send you Prevent serious injury or death replacement parts. Please call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437, 8 AM- 6 PM EST from falls or sliding out. - Page 3 Parts Tray Seat with Restraint System Seat Tube 2 Armrests Rear 2 Leg Caps Support 2 Retainers IMPORTANT! All consumer assembled 4 Legs screws must be fully tightened for proper assembly of this product. #10 x 2 " Screw - 4 Front Support Restraint Post...
- Page 4 DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. • Fit a leg cap into the openings of two legs, as shown.
- Page 5 Assembly Armrest Armrest #10 Lock Nut Front Rear Legs Front Support Arrows • Turn the leg assembly, as shown, so that the armrests point toward you. #10 x 2 " Screw - 2 • Position the front support so that the arrows are pointing toward you.
- Page 6 Assembly Recline Bar #10 Lock Nuts Front Rectangular Slots Front Front Support Circular Slots Seat Tube • Position the seat face down on a flat surface. • Insert the seat tube through the a rectangular slot, the two circular slots in the recline bar and then out through the other rectangular slot.
- Page 7 Assembly Seat Right End Left End of of Seat Seat Tube Tube Grooves Notch Armrest Armrest Lowest Openings Front Support Back View • Face the back of the seat assembly. • First, fit the left end of the seat tube into the lowest opening in the left armrest.
- Page 8 Assembly Upright #8 x " Screw Shown Actual Size Hole Seat Tube Seat Recline Arrows on • Squeeze the seat recline and Recline Bar push the seat back forward to the most upright position. Squeeze Arrows on Seat Tube • Align the arrows on the seat tube with the arrows on the recline bar.
- Page 9 Assembly Long Tabs Short Tab Short Tab Front Support Footrest • Fit the footrest over the front support and onto the long • Insert four #8 x screws " and short tabs on the seat. through the footrest and into #8 x "...
- Page 10 Assembly Seat Rear Support Footrest Retainers Back View • Position the assembly face down. #8 x " Screw - 2 #8 x 1 " Screw - 2 • Insert a #8 x " screw through each Shown Actual Size end of the seat and into the footrest.
- Page 11 Assembly Head Support Head Support Elastic Straps Elastic Straps Tabs Seat Back View • Place the pad onto the seat • From behind the seat, hook the elastic straps over the tabs • Insert the two top elastic straps through the slots labeled 1 labeled 3.
- Page 12 Assembly Elastic Straps Elastic Straps Slot Slot Slots Tabs • Lift the bottom of the pad. • Fit the elastic straps on the edge of the pad through the slots • Fit the elastic straps through Back View in the footrest. the in slots the seat bottom.
-
Page 13: Securing Your Child
IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if Buckle needed. Never substitute parts. -
Page 14: Using The Tray
Using the Tray WARNING Prevent serious injury or death from falls or sliding out. The child should be secured in the high chair at all times by the Slide Adjust Forward Forward or restraining system. The restraint to Remove Backward belts must be adjusted to fit your child snugly. -
Page 15: Adjusting The Seat Height
Adjusting the Seat Height Adjusting the Seat Angle Hint: Adjust the seat angle in any of four positions: Upright, WARNING Semi-Upright, Semi-Recline or Recline. Prevent serious injury or death from falls or sliding out. Upright It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. - Page 16 Lever • Lift the head support levers to lower supports. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. Printed in Mexico ©2002 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.