Adding And Deleting Channels - Panasonic DMR-E50K Operating Instructions Manual

Preparation
≥Confirm that the antenna is connected correctly.
≥Turn on the television and select the appropriate video input to
suit the connections to this unit.
1
Press [Í, DVD POWER] to turn the
unit on.
2
Press [3, 4] to select the menu lan-
guage and press [ENTER].
e.g., when you select
English
3
Press [ENTER].
Plug-in Auto Tuning starts and the unit puts the stations it
can receive into channels.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished. If the clock is an hour slower or
faster than the actual time, go to "Time Zone Adjust" to cor-
rect it ( page 49).
4
When the display shows the correct time
Press [ENTER] to complete Plug-in
Auto Tuning.
If the unit couldn't set the clock automatically
Press [ENTER] to show the "Manual Clock Setting" screen. Set the
time manually ( page 49).
To start Plug-in Auto Tuning again (after reloca-
tion, for example)
Antenna system, channel caption, and VCR Plusr guide
channel settings all revert to the default values when you
perform the procedure below. Timer recording settings are
also cleared.
When the unit is on and stopped
1 Press and hold [X, CH] and [W, CH] on the main unit for
about five seconds.
The unit turns off.
2 Press [Í, DVD POWER] to turn the unit on.
Follow the above steps 2–4.
If Plug-in Auto Tuning fails
1
Press [SETUP] to show the menus.
SETUP
Channel
Set Up
Disc
Video
Audio
Display
TV Screen
Select Language
Seleccione la Lengua
Sélection de Langue
English
Español
Français
Press ENTER
Pulse ENTER
Appuyer sur ENTER
Auto Channel/Clock Setting
Connect antenna cable and if you use a
cable box, tune it to your local PBS CH
then. . .
Please push the ENTER key.
ENTER
RETURN
Antenna System CATV
Auto Channel Setting
Channel Caption
Preset Channel Caption
Manual Channel Caption
VCR Plusi CH Setting
TAB SELECT
RETURN
2
Press [3, 4] to select "Channel" and
press [1].
SETUP
Channel
Set Up
Disc
3
Press [3, 4] to select "Antenna Sys-
tem" and press [ENTER].
SETUP
Channel
Set Up
4
Press [3, 4] to select "TV" or
"CATV" and press [ENTER].
The screen shown in step 2 reappears.
5
Press [3, 4] to select "Auto Channel
Setting" and press [ENTER].
SETUP
Channel
Set Up
Disc
Video
Audio
Display
If you have not yet set clock, the "Auto Channel/Clock Set-
ting" screen appears.
6
Press [ENTER].
Auto setting starts. This takes a few minutes. (To stop auto
channel setting, press [RETURN].) When finished, the Com-
plete screen or time display is shown. Press [ENTER].
To return to the previous screen
Press [RETURN].
When you are finished
Press [SETUP].

Adding and deleting channels

Add or delete channels if necessary channels are not set or unnec-
essary channels are set.
While this unit is receiving the antenna signal (but not during
recording):
1
Press the numbered buttons to select
a channel.
e.g., "5": [0] [5]
"15": [1] [5]
"115": [100] [1]
≥You can also use [W, X, CH]
when you are going to delete a channel.
2
Press [ADD/DLT].
The channel is deleted if it was set or added if it was not set.
e.g.,
Repeat steps 1 and 2 as necessary.
Antenna System CATV
Auto Channel Setting
Channel Caption
Preset Channel Caption
Manual Channel Caption
Antenna System
TV
CATV
Auto Channel Setting
Connect antenna cable and if you use a
cable box, tune it to your local PBS CH
then...
Please push the ENTER key.
Unit's display
[5]
CHANNEL 15 DELETED
7
RQT6920