Hifonics BE35 500.4 Quick Start Installation Manual

Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
Power cable size
Model
and fusing
It is critical to use the proper power
BE35-500.4
and ground cable. Select the size
listed here for your amplifier model. BE35 800.4
Always use high quality copper
BE35 1200.1D 1 x 80A Maxi
cable. Visit our website for multi amp
system cable recommendations.
2 x 70A Maxi
BE35 1700.1D
External 200A
BE35 2100.1D
Be sure to use the proper fuse size
for each model. Some models require
External 250A
BE35 2500.1D
an external fuse.
External 100A
BE35 5000.5
Installation
Disconnect
1
negative battery
terminal
Place terminal in a secure
position so that it won't
accidentally contact the
negative battery post
Run Cables
2
Properly route power,
speaker and RCA cables
through the vehicle.
Mount Amplifier
3
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplifier to
a secure surface. Do not mount
the amplifier upside down.
Chassis Ground
4
The chassis ground connection
is critical to the performance
of the amplifier. Choose a
location that is close to the
amplifier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Fuse Size Cable Size Negative Power
5
Connection
4ga
2x25A ATC
Attach the chassis ground
4ga
2x35A ATC
cable to the amplifier
4ga negative terminal. It is
important to make sure this
2ga
connection is very tight.
0ga
Remote Turn-on
6
0ga
Connection
2ga
Attach the remote turn on
wire to the amplifier remote
output of the source unit.
Positive Power
7
Connection
Attach the main power cable
to the amplifier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Signal Input
8
Connection
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplifier.
9 Level Control
Bare metal
BRIDGED
LEFT RIGHT
SPEAKER OUTPUT
BRIDGED
BRIDGED BRIDGED
LEFT RIGHT
LEFT RIGHT CH 3 CH 4
SPEAKER OUTPUT
SPEAKER OUTPUT SPEAKER OUTPUT
BRIDGED
BRIDGED
LEFT RIGHT CH 1 CH 2
SPEAKER OUTPUT SPEAKER OUTPUT SPEAKER
BRIDGED
CH 3 CH 4
SPEAKER OUTPUT
Turn the LEVEL control completely
INPUT INPUT
counter-clockwise to minimum. LEVEL LEVEL SUBSONIC
15
9V 0.2V 6V 0.2V
PHASE LPF LPF
Speaker
10
Connections
BRIDGED BRIDGED
LEFT RIGHT
CH 3 CH 4
Connect the speaker cables to
the speaker output connectors.
SPEAKER
SPEAKER OUTPUT Follow the diagram below SPEAKER OUTPUT
that best fits your speaker
configuration.
Stereo
BRIDGED BRIDGED
BRIDGED
LEFT RIGHT CH 1 CH 2
LEFT RIGHT
BRIDGED
CH 3 CH 4
SPEAKER OUTPUT SPEAKER OUTPUT SPEAKER
SPEAKER
SPEAKER OUTPUT
SPEAKER OUTPUT
BRIDGED
BRIDGED
CH 3 CH 4
LEFT RIGHT
Monoblock
single woofer
BRIDGED SPEAKER OUTPUT
SPEAKER
CH 1 CH 2
SPEAKER OUTPUT SPEAKER OUTPUT SPEAKER OUTPUT SPEAKER OUTPUT
BRIDGED
CH 3 CH 4
Positive Battery
11
Connection
SPEAKER OUTPUT
OUTPUT SPEAKER OUTPUT
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Be prepared to disarm your vehicle's alarm and
to enter your radio / source unit code.
Re-connect
12
Negative Battery
Terminal
XOVER MODE
Re-connect the negative
SUBSONIC
battery terminal making sure it
is securely tightened.
MONO STEREO
FULL HP
LP
35Hz 10 40Hz
XOVER MODE
LPF
OUTPUT SPEAKER OUTPUT
Bridged
BRIDGED
CH 3 CH 4
OUTPUT SPEAKER OUTPUT SPEAKER
OUTPUT SPEAKER OUTPUT
SPEAKER OUTPUT
BRIDGED
CH 1 CH 2
Monoblock
multiple woofers
BRIDGED
OUTPUT SPEAKER OUTPUT SPEAKER
LEFT RIGHT
SPEAKER OUTPUT
SPEAKER OUTPUT
BRIDGED
CH 3 CH 4
SPEAKER OUTPUT
SPEAKER OUTPUT
SPEAKER OUTPUT