Hifonics BG-1000.4 Quick Start Installation Manual

Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
Power cable size
Model
and fusing
It is critical to use the proper power
BG-1000.4
and ground cable. Select the size
BG-1600.4
Always use high quality copper
BG-1300.1D
cable. Visit our website for multi amp
BG-1900.1D
system cable recommendations.
BG-2200.1D
BG-2500.1D
Be sure to use the proper fuse size
BG-3300.1D
for each model. Some models require
an external fuse.
Installation
Disconnect
1
negative battery
terminal
Place terminal in a secure
position so that it won't
accidentally contact the
negative battery post
Run Cables
2
Properly route power,
speaker and RCA cables
through the vehicle.
3
Choose a mounting location
that will provide adequate air
a secure surface. Do not mount
Chassis Ground
4
The chassis ground connection
is critical to the performance
location that is close to the
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Negative Power
5
Fuse Size Cable Size
Connection
60A
Attach the chassis ground
100A
50A x 2
negative terminal. It is
4ga
60A x 2
important to make sure this
External 150A connection is very tight.
External 200A
External 250A
Remote Turn-on
6
Connection
Attach the remote turn on
output of the source unit.
Positive Power
7
Connection
Attach the main power cable
cable must run directly to
the battery and be properly
fused and be very tight.
Signal Input
8
Connection
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
9 Level Control
Bare metal
BRIDGED
LEFT RIGHT
SPEAKER OUTPUT
BRIDGED
BRIDGED BRIDGED
LEFT RIGHT
LEFT RIGHT CH 4
CH 3
SPEAKER OUTPUT
SPEAKER OUTPUT SPEAKER OUTPUT
BRIDGED
BRIDGED
CH 1 CH 2
LEFT RIGHT
SPEAKER OUTPUT SPEAKER OUTPUT SPEAKER
BRIDGED
CH 3 CH 4
BRIDGED
LEFT CH1/2 RIGHT
SPEAKER OUTPUT
Turn the LEVEL control completely
INPUT INPUT
SPEAKER OUTPUT
counter-clockwise to minimum. LEVEL LEVEL SUBSONIC
15
9V 0.2V 6V 0.2V
PHASE LPF LPF
BRIDGED BRIDGED
Speaker
10
BRIDGED
Connections
LEFT RIGHT
Connect the speaker cables to
the speaker output connectors.
SPEAKER OUTPUT SPEAKER
Follow the diagram below
Stereo
BRIDGED
LEFT RIGHT
BRIDGED
CH 3 CH 4
SPEAKER OUTPUT SPEAKER
SPEAKER OUTPUT
SPEAKER OUTPUT
Monoblock
single woofer
BRIDGED
CH 1 CH 2
SPEAKER
SPEAKER OUTPUT SPEAKER OUTPUT
SPEAKER OUTPUT SPEAKER OUTPUT
BRIDGED
LEFT CH1/2 RIGHT
BRIDGED
CH 3 CH 4
Positive Battery
11
SPEAKER OUTPUT SPEAKER
Connection
SPEAKER OUTPUT
OUTPUT SPEAKER OUTPUT
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
CH 1 CH 2 CH 3
Be prepared to disarm your vehicle's alarm and
to enter your radio / source unit code.
BRIDGED
BRIDGED
LEFT CH3/4 RIGHT
Re-connect LEFT CH3/4 RIGHT
12
SPEAKER OUTPUT SPEAKER
Negative Battery
Terminal
XOVER MODE
SPEAKER OUTPUT
Re-connect the negative SPEAKER OUTPUT
SUBSONIC
battery terminal making sure it
is securely tightened.
Speakers
MONO STEREO
FULL HP
LP
35Hz 10 40Hz
XOVER MODE
LPF
BRIDGED
CH 3 CH 4
SPEAKER OUTPUT
OUTPUT
Bridged
BRIDGED
BRIDGED BRIDGE
CH 1 CH 2
LEFT RIGHT CH 3
OUTPUT SPEAKER OUTPUT
SPEAKER OUTPUT SPEAKER
SPEAKER OUTPUT
BRIDGED
BRIDGED BRIDGE
CH 4
CH 3
Monoblock LEFT RIGHT CH 1
multiple woofers
BRIDGED
LEFT RIGHT
OUTPUT
SPEAKER OUTPUT SPEAKER
SPEAKER OUTPUT
SPEAKER OUTPUT
BRIDGE
CH 3
BRIDGED
BRIDGED
LEFT CH3/4 RIGHT
LEFT CH3/4 RIGHT
SPEAKER
SPEAKER OUTPUT
OUTPUT
SPEAKER OUTPUT
BRIDGED BRIDG
LEFT CH1/2 RIGHT LEFT CH3
CH 4 CH 5
SPEAKER OUTPUT
SPEAKER OUTPUT SPEAKER
OUTPUT
Subwoofer
CH 1 CH 2 CH 3