Advertisement
Advertisement
Table of Contents
Related Manuals for Hifonics BRUTUS BRX160.2
Summary of Contents for Hifonics BRUTUS BRX160.2
- Page 1 BRX160.2 / BRX320.4 / BRX640.4 / BRX1200.4 BRX5000.5...
-
Page 2: General Installation Procedure
GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion. -
Page 3: Amplifier Feature Descriptions
4, 2 and 1-Ohm loads. All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, and Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable amplifiers. - Page 4 - 1/2CH X-OVER: FULL BRUTUS MONO Here we show how to use the 2 channel amplifiers as a 1 channel unit by taking advantage of the mono bridging capability of all Hifonics amplifiers Switch setting checklist: - 1/2CH X-OVER: LP Interconnect cable checklist:...
- Page 5 2 or 3 CHANNEL SYSTEM Here we show how to use the 4 channel amplifiers as a 3 channel unit by taking Crossover frequency control checklist: advantage of the mono bridging capability of all Hifonics amplifiers. Channels 1/2: - HI PASS: N/A The following example shows how to create a 3 channel system by mono - LOW PASS: 11 o’clock...
- Page 6 BRX320.4 / BRX640.4 / BRX1200.4 4-CHANNEL AMPLIFIER APPLICATIONS Front/Rear high pass, using a mono amplifier for mono sub bass The combination of a mono and a 4 channel amplifier, utilizing their built in crossovers, makes it a snap to put together a full system with front and rear Crossover frequency control checklist: highs, with mono sub bass.
- Page 7 BRX5000.5 5-CHANNEL AMPLIFIER APPLICATIONS 5 channel discrete, one being mono low pass You can use this configuration simply as 4 discrete full range channels, with a 5th - CH 3 / 4 X-OVER: FULL low pass channel. All of the crossovers are bypassed , except the LOW PASS on channel 5.
- Page 8 BRX1100.1D / BRX1600.1D MONO AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the Minimum final loudspeaker impedance: full range primary amplifier with good quality RCA cables. A “Y” adapter - 1 ohm.
- Page 9 BRX2000.1D MONO AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the Minimum final loudspeaker impedance: full range primary amplifier with good quality RCA cables. A “Y” adapter - 1 ohm.
-
Page 10: Basic Application
BRX2400.1D MONO AMPLIFIER APPLICATIONS Basic application SINGLE AMP INSTALLATION PROCEDURE: FULL RANGE 1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out STEREO LINE INPUT Y-ADAPTOR puts with good quality RCA interconnect cables. 2. Plug in the HFR-3 remote module into the amp REMOTE INPUT jack. 3. -
Page 11: Setting Up Systems After Installation For Best Performance
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE BRX160.2 / BRX320.4 / BRX640.4 / BRX1200.4 / BRX5000.5 General: At this point you are ready to get more specific on the settings for your amplifier. High Pass: -When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. -
Page 12: Troubleshooting A System
+12 volt and remote leads to localize the problem. 4 - If the HIFONICS lettering is illuminated but you do not have Power or Protection illuminated, simply remove your remote wire and use a jumper wire from 12V+ on the amplifier to the Remote connection on the amplifier. - Page 13 HIFONICS AMPLIFIERS CAR AMPLIFIERS...