Initial Operation - Metabo KHA 18 LTX BL 24 Quick Original Instructions Manual

Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- Crystalline silica from bricks and cement and other
masonry products, and
- Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
This also applies to dust from other materials such as
some timber types (like oak or beech dust), metals,
asbestos. Other known diseases are e.g. allergic
reactions, respiratory diseases. Do not let dust enter
the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this way,
fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the exhaust
air stream at yourself or nearby persons or on dust
deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or blowing
stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
5. Overview
See page 2.
1 Keyless chuck *
2 Keyless chuck sleeve *
3 Chuck lock
4 Tool lock
5 SDS chuck
6 Spindle
7 Additional handle
8 Depth stop
9 Metabo VibraTech (MVT)
10 Rotation selector switch
11 Trigger switch
12 Lock
13 Switch button (for changing the operating
mode)
14 Guide groove for the dust extraction ISA 18
LTX
15 Battery pack release button
16 Rubber cover for dust protection of the power
supply for the dust extraction ISA 18 LTX
17 LED light to illuminate the workplace
18 Capacity indicator button
19 Capacity and signal indicator
20 Battery pack
* depending on model

6. Initial Operation

6.1 Assembly of the additional handle
For safety reasons, always use the additional
handle supplied.
Open the clamping ring by turning the additional
handle (7) anticlockwise. Push the additional
handle onto the collar of the machine. Insert the
depth stop (8). Securely tighten the additional
handle at the angle required for the application.
6.2 Battery pack
Charge the battery pack (20) before use.
Recharge the battery pack if performance
diminishes.
The ideal storage temperature is between 10°C
and 30°C.
Li-Ion battery packs "Li-Power, LiHD" have a
capacity and signal indicator (19):
- Press the button (18); the LEDs indicate the
charge level.
- The battery pack is almost flat and must be
recharged if one LED is flashing.
6.3 Removing and inserting the battery pack
Removing:
Press the battery pack release (15) button and
remove the battery pack (20).
Inserting:
Slide in the battery pack (20) until it engages.
7. Use
7.1 Depth Stop Setting
Loosen the additional handle (7). Set depth stop
(8) to the desired drilling depth and retighten
additional handle. (7)
7.2 Switching On and Off
To start the machine, press the trigger (11). The
speed can be changed at the trigger.
Release the trigger (11) to switch off.
7.3 Operating mode selection
Press (12) the lock and turn the thumbwheel (13).
Drilling
ENGLISH en
9