Reassembling The Mask; Limited Warranty - ResMed Ultra Mirage II User Manual

If any visible deterioration of a mask
•
component is apparent (cracking,
crazing, tears etc), the mask
6 Reconnect the forehead support to the
component should be discarded and
replaced.
R M
EPROCESSING THE ASK
7 Fit the grooved edge of the nasal
P
BETWEEN ATIENTS
The mask should be reprocessed when
used between patients.
Cleaning, disinfection and sterilization
instructions are available from the ResMed
website, www resmed.com/masks/
sterilization/americas.
8 Connect the headgear clips to the mask
If you do not have Internet access, please
contact your ResMed representative.
R M
EASSEMBLING THE ASK
See section E on the illustrations sheet.
1 Insert the ports cap into the ports. Make
sure the tabs of the ports cap face away
from the mask.
T
2 Insert the mask elbow into the mask
frame and secure it with the elbow clip P
on the inside of the frame (Fig. E-1). The
See section A on the illustrations sheet.
flat side of the elbow clip must face the
D
mask frame. If you have fitted the mask
elbow correctly, it should not move
Dead space is the empty volume of the
when you try to firmly pull it away from
mask up to the swivel.
the frame.
The dead space of the mask varies
3 Grasp the edges of the vent cover on
according to cushion sizes but is less than
both sides of the "Click" sticker at the
135 mL.
same time. Firmly push the vent cover
onto the mask elbow to make sure it is
Note:
clicked securely in place (Fig. E-2).
to change these specifications without notice.
4 Push the swivel onto the end of the
mask elbow.
5 Attach the forehead pads to the
forehead support by inserting the pad
plugs into the two holes on the back of
the forehead support (Fig E-3). Push the
pads firmly against the forehead support
R P L
EPLACEMENT ARTS
ResMed warrants that your ResMed mask
Part No. Item
system, including its components: mask
16563 Cushion clip
frame, cushion, headgear, tubing and other
16557 Cushion, Large
accessories ("Product") shall be free from
16558 Cushion, S hallow
defects in material and workmanship for a
period of ninety (90) days from the date of
16735 Cushion, S hallow-wide
purchase by the initial consumer.
16556 Cushion, S tandard
For further details refer to the Warranty.
16566 Elbow assembly
16572 Elbow clip (1 pk.)
16573 Elbow clip (10 pk.)
60123 Forehead pads (1 pk.)
60124 Forehead pads (10 pk.)
16590 Forehead support with pads
16594 Frame assembly
16728 Frame System with Cushion,
Large
16727 Frame System with Cushion,
S hallow
16736 Frame System with Cushion,
S hallow-wide
16726 Frame System with Cushion,
S tandard
16119 Headgear, Large
16117 Headgear, S tandard
16118 Headgear, S mall
16569 Headgear clip (2 pk.)
16734 Headgear clip (10 pk.)
16560 Mask frame
16570 Ports cap/s (2 pk.)
16571 Ports cap/s (10 pk.)
16565 Swivel
16575 Vent cover
to ensure that the pads fit securely into
the forehead support.
mask frame. Depress the tab and move
the forehead support into one of the
four tab positions (Fig. E-4).
cushion to the mask frame. Fit the top
section first, then work your way around
the mask, pushing the cushion onto the
frame, ensuring a good seal has been
achieved. Push the cushion clip over the
cushion onto the mask frame, ensuring it
clicks into place in all locations (Fig. E-5).
frame. Thread the headgear straps
through the slots on the forehead
support and the headgear clips. The
U M headgear label should
LTRA IRAGE
face outwards and be near your neck
when fitted. Fasten the Velcro straps.
S
ECHNICAL PECIFICATIONS
–F C
RESSURE LOW URVE
S I
EAD PACE NFORMATION
The manufacturer reserves the right
W
IMITED ARRANTY