Bosch Professional GDR 18V-200 C Original Instructions Manual page 15

Cordless impact screwdriver
Data transfer
C)
Bluetooth®
Signal interval
D)
Max. signal range
Frequency range used
Output power
Recommended ambient temperat-
ure during charging
Permitted ambient temperature dur-
E)
ing operation and during storage
Recommended rechargeable batter-
ies
Recommended chargers
A) Measured at 20−25 °C with rechargeable battery GBA 18V 5.0Ah.
B) Depends on battery in use
C) The mobile terminal devices must be compatible with Bluetooth® Low Energy devices (version 4.1) and support the Generic Access Profile
(GAP).
D) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be signi-
ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).
E) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 98.5 dB(A); sound power level
109.5 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to
EN 62841-2-2:
Tightening screws and nuts of the maximum permitted size:
2
GDR 18 V-200 C: a =9.8 m/s , K=1.5 m/s
h
2
GDX 18 V-200 C: a =9.0 m/s , K=1.5 m/s
h
2
GDS 18 V-200 C: a =11.2 m/s , K=1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
Bosch Power Tools
GDR 18V-200 C
Bluetooth® 4.1
(Low Energy)
s 8
m 30
MHz 2 402–2 480
mW < 1
°C 0 to +35
°C –20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
2
from unintentionally pressing the on/off switch.
2
2
Battery Charging
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
English | 15
GDX 18V-200 C GDS 18V-200 C
Bluetooth® 4.1 Bluetooth® 4.1
(Low Energy) (Low Energy)
8
30
2 402–2 480 2 402–2 480
< 1
0 to +35
–20 to +50 –20 to +50
GBA 18V... GBA 18V...
ProCORE18V... ProCORE18V...
GAL 18... GAL 18...
GAX 18... GAX 18...
GAL 36... GAL 36...
160992A5UW | (14.07.2020)
8
30
< 1
0 to +35