Whirlpool CAM2752 Installation Instructions Manual page 28

ELECTRONICCONTROL SETUP INSTRUCTIONS
How to Use the Buttons to Program the Controls
1. The COTTON/WHITES button is used to adjust the values
associated with set-up codes. Pressing the button will
change the value by increments. Rapid adjustment is
possible by holding down the button.
2. The PERM PRESSbutton will advance through the set-up
codes. Pressing this button will advance to the next available
set-up code. Holding down the button will automatically
advance through the set-up codes at a rate faster than 1 per
second.
3. The COLORS/DELICATESbutton is used to select or deselect
options.
Start Operating Set-up
Insert service access door key, turn, and lift to remove service
access door.
Dryers with Card Reader Installed:
Once the debit card reader is installed (according to the
reader manufacturer's instructions), the set-up mode can be
entered by inserting a manual set-up card (supplied by the
reader manufacturer) into the card slot. If manual set-up card
is not available, only the diagnostic mode can be entered by
removing the service access door.
IMPORTANT: To access set-up mode or diagnostic mode, use
a service key to open the service access door. If a card reader
is installed, a service card is available for accessing diagnostics.
If a service key is not available, the AA1 connector must be
removed for access. The console must not be opened unless
power is first disconnected from the dryer. To access connector
AAI:
1. Unplug dryer or disconnect power.
2. Open console, remove plug on AA1, close console.
3. Plug in dryer or reconnect power.
The dryer is now in the set-up mode.
NOTE: It is not necessary to set up the dryer with the following
codes; the dryer is pre-set at the factory. These codes can be
used to change settings, if desired.
Set-Up Codes
[] The PERM PRESSbutton will advance from code to code.
[] The COTTON/WHITES button will change the code value.
[] The COLORS/DELICATESbutton will select or deselect
options.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or
three right-hand characters.
NOTE: The first line of each code indicates the factory default.
Code Explanation
6 06 REGULAR CYCLE PRICE
6 06
601
When the d.xx is set to d.00, this 6 xx value represents
the number of quarters (coin 1) needed to start
the dryer; may adjust from 0-39. Change this value
by pressing the COTTON/WHITES button. 6 06 = 6
quarters = 51.50.
When the d.xx is set to d.CS, this 6 xx value represents
the number of push-in actuations of the coin slide
to start the dryer. 6 01 would equal one coin slide
activation.
• Press the PERM PRESSbutton once to advance to
next code.
7 05 REGULAR DRY TIME
7 05
7 30
When set to Coin Drop or Card Reader operation, the
dry time equals the Regular Dry Time value multiplied
by the Regular Cycle Price value. Example: 6 06 and
7 05 = (06 x 05 = 30 minutes).
For coinslide or OPL operation, the value is the amount
of minutes of dry time. Factory default of 30 minutes.
Pressing COTTON/WHITES adjusts the value from 1-99
minutes.
Press the PERM PRESSbutton once to advance to
next code.
8 00 TYPE OF DRYER PRICING
8 00
8 FC
9 00
9 O0
90C
Fixed Cycle with Top Off. Only available for use with
coin drops or card readers. For detailed description,
see General User Information.
Fixed Cycle. For detailed description, see General User
Information. Use COLORS/DELICATES button to make
this selection.
Press the PERM PRESS button once to advance to
next code.
CYCLECOUNTER OPTION
This option is either NOT SELECTED"OFF" or SELECTED
"ON."
Not Selected "OFF."
Selected "ON" and not able to be deselected.
Press the COLORS/DELICATES button
3 consecutive times to select "ON." Once
selected "ON" it cannot be deselected.
Press the PERM PRESS button once to advance to
next code.
28