Fishman SA330x User Manual
  1. Manuals
  2. Brands
  3. Fishman Manuals
  4. Amplifier
  5. SA330x
  6. User manual

Fishman SA330x User Manual

Hide thumbs

Advertisement

Table of Contents

USER GUIDE
fishman.com
SA330x

Advertisement

Table of Contents
loading

Related Manuals for Fishman SA330x

Summary of Contents for Fishman SA330x

  • Page 1 USER GUIDE fishman.com SA330x...

  • Page 2: Important Safety Instructions

    The mains plug/appliance coupler is used as disconnect device, the disconnect device shall remain readily operable. Copyright © 2016 FISHMAN TRANSDUCERS, INC. All rights reserved. No part of this document may be reproduced in any form without the written permission of FISHMAN TRANSDUCERS, INC.
  • Page 3 NOTE: Fishman Transducers, Inc. is not responsible for unauthorized equipment modifications that could violate FCC rules, and/ or void product safety certifications. EU Declaration of Conformity CE: Hereby, Fishman declares that this SA330x is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU, 2014/35/EU. The Declaration of Conformity can be found at www.fishman.com/support.
  • Page 4 Setting the SA330x on its Stand When the SA330x is used as a portable PA system it is imperative that it be used with the included tripod speaker stand, and that it be placed directly on a level, solid, flat surface.
  • Page 5 SA330x over. Setting SA330x Controls Locate the Power switch and switch it off, then connect the AC line cord into the back of the SA330x. Plug the SA330x into an electrical outlet with the appropriate AC voltage.

  • Page 6: Front Panel Controls

    Front Panel Controls The following pages describe the functions of each control or jack on the front and rear panels of the SA330x. Refer to these numbered diagrams for each numbered control on the following pages. 1. Mute – The Mute switch silences the signals from Channels 1 and 2 to the speakers and all the XLR outputs.
  • Page 8 14. Aux In – Use this to control the level of a device plugged into the Aux inputs. Note that the Aux channel is independent of the Mute switch. 15. Monitor – Use this to control the level of a second SA330x connected in the Monitor I/O setup as shown on page 13.

  • Page 10: Rear Panel Controls

    This pre-EQ output is always ground- isolated to prevent ground loop hum. 22. Monitor In & Out – The monitor feature on the SA330x allows two performers, each with an SA330x, to send their own mix to each other for simplified on-stage monitoring.
  • Page 11 This device complies with part 15 of the FCC rules. Operation is subject to the following two Name: Performance Audio conditions: (1) this device may not cause harmful interference, and (2) this device must accept any System SA330x interference received, including interference that may cause undesired operation. Model: 494-000-414 Suitable for home or office use.

  • Page 12: About Acoustic Feedback

    About Acoustic Feedback There are two features to help control acoustic feedback when using the SA330x with a microphone or acoustic instrument – the Phase switch and the Anti-Feedback notch control. Feedback usually occurs when the natural resonances of a microphone or an instrument react with amplified sound.
  • Page 13 LED. To restore normal operation, turn the SA330x power off for at least 10 seconds, then ON again, and power to the device will be restored.

  • Page 14: Block Diagram

    Block Diagram...

  • Page 15: Technical Specifications

    Technical Specifications Input Impedance: 1/4” Input 5M Ohm XLR Input 3k Ohm Balanced Aux Input (stereo) 10k Ohm Tone Controls and Anti-Feedback: ±12.5dB @ 50Hz (resonant) ±10.5dB @ 750Hz (resonant) High ±12.5dB @ 10kHz (shelving) Anti Feedback range -14dB @ 15Hz – 330Hz (Hi-Q resonant notch) Channel 1 &...
  • Page 16 Fishman and Fishman Transducers are trademarks or tradenames of Fishman Transducers Inc. 513-300-234_r2 7/16...

Table of Contents