Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Xerox Manuals
  4. Printer
  5. WorkCentre M118
  6. Remanufacturing instructions

Xerox WORKCENTRE M118 Remanufacturing Instructions

Drum cartridge remanufacturing
Hide thumbs Also See for WORKCENTRE M118:

Advertisement

Quick Links

Download this manual
XEROX
WORKCENTRE M118 • 128
®
DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
XEROX
WORKCENTRE M118 DRUM CARTRIDGE
®
www.uninetimaging.com
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact techsupport@uninetimaging.com

Advertisement

loading

Related Manuals for Xerox WORKCENTRE M118

Summary of Contents for Xerox WORKCENTRE M118

  • Page 1 XEROX WORKCENTRE M118 • 128 ® DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS XEROX WORKCENTRE M118 DRUM CARTRIDGE ® www.uninetimaging.com © 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.

  • Page 2: Supplies Required

    XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS REMANUFACTURING THE XEROX WORKCENTRE M118/128 DRUM CARTRIDGE By the Technical Staff at UniNet SUPPLIES REQUIRED 1. Xerox WorkCentre M 118/128 developer (used in OPC cartridge) 2. Xerox WorkCentre M 118/128 drum cartridge replacement chip 3.
  • Page 3 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 2. Remove the four screws from the inner end cap. Remove the end cap. 3. Follow the wires from the inner end cap to the sensor. Pry up on the two locking tabs and remove the sensor.
  • Page 4 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 4. On the non gear side, remove the four screws from the end cap. Remove the end cap. 5. On the large gear side, remove the metal plate and the drum bushing.
  • Page 5 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 6. On the opposite side (non gear side) pry off the white gear and the drum bushing. 7. Carefully separate the two halves. 8. Remove the drum and place aside. www.uninetimaging.com ©...
  • Page 6 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 9. Remove the PCR. 10. Remove the two screws from the wiper blade. Remove the blade. 11. Clean out any toner from the hopper. Make sure you also clean out the auger post.
  • Page 7 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 12. Install the new wiper blade and two screws. 13. Clean the PCR with your normal cleaner. Wipe off the old conductive grease from the shaft and replace. Re-install the PCR in the assembly grease side to the black PCR holder.
  • Page 8 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 16. Remove the plastic spring arm, and the two screws. 17. Remove the screw from the contact plate on the opposite 18. Carefully pry up the three plastic tabs on the back edge of side of the hopper.
  • Page 9 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 19. Lift off the cover and locate the chip. 20. From the inside of the cover remove and replace the chip. 21. Remove all the old developer from the hopper. 22. Pour in the new developer.
  • Page 10 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 23. Snap the cover back in place. 24. Install the back screw in front of the metal cover. Make sure all three tabs lock! 25. Install the plastic spring arm and the screw to hold it in 26.
  • Page 11 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 27. Install both springs on the metal cover. 28. While holding both halves together, install the drum bushings (the pointed one to the gear side with the metal plate). www.uninetimaging.com © 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
  • Page 12 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 29. Install the double bushing to the non-gear side. Also install the white gear onto the keyed shaft. 30. Install the end cap and four screws on the non-gear side. Make sure the white gear fits properly.
  • Page 13 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 31. Install the inner handle end cap on the gear side and the three screws. Watch the wire routing so that they do not get pinched. 32. While holding the cartridge so the developer will not spill out, remove the tape from the sensor hole.
  • Page 14 XEROX WORKCENTRE M118 • 128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS 33. Install the outer end cap onto the gear side, and the two screws. Press down on the handle to allow the end cap to fit properly. www.uninetimaging.com © 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.

This manual is also suitable for:

Workcentre m128