Ic7002 (Ba5948Fpe2) Ic 4Ch Drive; Ic807 (Mn101Ef16Zxw) Microprocessor - Panasonic SA-NS55E Service Manual

18.2. IC7002 (BA5948FPE2) IC 4CH Drive

Pin No. Mark
1 IN2
2 PC2
3 IN1
4 PC1
5-8 N.C.
9 PGND1
10 PVCC1
11 D1-
12 D1+
13 D2-
14 D2+

18.3. IC807 (MN101EF16ZXW) MICROPROCESSOR

Pin No. Mark I/O
1 PCONT1
2 PCONT2
3 N.C.
4 FL_DATA/OCD
_SDA
5 USB_RST
6 FL_CLK/OCD_
SCL
7 USB_REQ
8 N.C.
9 N.C.
10 D_PCONT
11 MMOD
12 OSC2 (8MHz)
13 OSC1 (8MHz)
14 VSS
15 XI (32KHz)
16 XO (32KHz)
17 VDD33
18 VDD18
19 NRST
20 VOL_JOG1
21 VOL_JOG2
22 FL_RST
23 FL_CS
24 DAB_PCONT
25 RMT
26 HALT
27 DAB_
DDOWFIC/MX
MUTE
28 DAB_IRQ/I2S
RATE
29 BLKCK
30 N.C.
31 CD_MDATA
32 STAT
33 CD_MCLK
34 USB_SDA I/O
35 CD_MLD
36 USB_SCL
37 VDD18
38 N.C.
39 VSS
I/O Function
I Motor Driver Input
I Turntable Motor Drive Signal
("L":ON)
I Motor Drive (1) Input
- Traverse Motor Drive Signal
("L"): ON)
- No Connection
- Ground Connection (1) for Drive
- Power Supply (1) for Drive
O Motor Drive (1) reverse - action
output
O Motor Drive (1) forward - action
output
O Motor Drive (2) reverse - action
output
O Motor Drive (2) forward - action
output
Function
O APower Control Output 1 (Pwr
Sply,Active HIGH)
O Power Control Output 2
- No Connection
O On Chip Debugger Data
O USB Reset Pin
O On Chip Debugger Clock
I USB Interrupt Request
- No Connection
- No Connection
O Dport Power control
I Memory mode selection
O Main Oscillator output (8MHz)
I Main Oscillator input (8MHz)
- Micom GND
I Slow Oscillator input (32KHz)
O Slow Oscillator output (32KHz)
- Voltage supply (3.3V)
- Internal output (1.8V)
I MICOM RESET PIN (L: reset)
I Jog Input 1
I Jog Input 2
- No Connection
O Chip Select for FL Panel
- No Connection
I Remote Control Input
I AC Failure Detect Signal
- No Connection
- No Connection
I CD Subcode Block Clock Input
- No Connection
O CD LSI Command Data
I CD LSI Status Input
O CD LSI Command Clock
USB I2C Data Line
O CD LSI Command Load
I USB I2C Clock Line
- Power Supply (1.8V)
- No Connection
- Micom GND
Pin No. Mark
15 D3-
16 D3+
17 D4-
18 D4+
19 PVCC2
20 PGND2
21-24 N.C.
25 VCC
26 VREF
27 IN4
28 IN3
Pin No. Mark
40 ASP_CLK
41 ASP_DATA
42 E_DATA
43 E_CLK
44 E_CS
45 CD_RST
46 N.C.
47 Demo_Set
48 N.C.
49 N.C.
50 TU_SDA
51 TU_CLK
52 N.C.
53 USB_MMOD
54 TU_TUNED
55 TU_STEREO
56 AD_REV
57 AD_FWD
58 AD_RSKIP
59 AD_FSKIP
60 AD_STOP
61 AD_PLAY
62 CRTIMER
63 VSS
64 VERR
65 CLOSE_L
66 OPEN_H
67 LINKACTIVE
68 DAC_RESET
69 ANT_REV
70 XM_RST
71 TERR
72 XM_TX_OUT
73 RDS_DATA
74 RDS_CLK
75 XM_PCONT
76 UART_IN
77 UART_OUT
78 MECH_FIN
73
SA-NS55E / SA-NS55EG
I/O Function
O Motor Drive (3) reverse - action
output
O Motor Drive (3) forward - action
output
O Motor Drive (4) reverse - action
output
O Motor Drive (4) forward - action
output
- Power Supply (2) for Driver
- Ground Connection (2) for Driver
- No Connection
- Power Supply terminal
- Reference Voltage Input
I Motor Driver (4) Input
I Motor Driver (3) Input
I/O Function
O ASP Sound Processor Serial
Clock Output
O ASP Sound Processor Serial
Data Output
I/O EEPROM DATA I/O
O EEPROM CLOCK
O EEPROM CS
O CD LSI Reset Ouput (L: reset)
O No Connection
I Demo Mode Setting Input
- No Connection
- No Connection
I/O IIC Serial Data for Tuner (PLL
Data I/O)
O IIC Serial Clock for Tuner (PLL
Clock Output)
- No Connection
O 0: Start from Main Area, 1:Start
from boot area
I/O Tuner Tuned Signal
I/O Tuner Stereo Signal
O Dport AD_CNTL
O Dport AD_CNTL
O Dport AD_CNTL
O Dport AD_CNTL
O Dport AD_CNTL
O Dport AD_CNTL
- CR TIMER
- Micom GND
I Verify Error
O CD Tray Close Control (Active
L)
O CD Tray Open Control (Active
H)
- No Connection
- No Connection
- No Connection
- No Connection
I Timeout Error
- No Connection
I RDS DATA Input
I RDS Clock Input
- No Connection
O Dport Serial Comm
I Dport Serial Comm
O Mecha Movement - Forward