Table of Contents
Advertisement
20.2. IC7002 (BA5948FPE2) IC 4CH Drive
Pin No.
Mark
1
IN2
2
PC2
3
IN1
4
PC1
5-8
N.C.
9
PGND1
10
PVCC1
11
D1-
12
D1+
13
D2-
14
D2+
20.3. IC803 (MN101EF16ZXW) MICROPROCESSOR
Pin No.
Mark
I/O
1
PCONT1
2
PCONT2
3
N.C.
4
FL_DATA /
OCD_SDA
5
USB_RST
6
FL_CLK /
OCD_SCL
7
USB_REQ
8
N.C.
9
N.C.
10
N.C.
11
MMOD (GND)
12
OSC2 (8MHz)
13
OSC1 (8MHz)
14
VSS
15
XI (32kHz)
16
XO (32KHz)
17
VDD3.3
18
VDD1.8
19
NRST
20
N.C.
21
MMOD0
22
TERR
23
VERR
24
DAB_PCONT
25
RMT
26
HALT
27
DAB_
DDOWFIC
28
DAB_IRQ
29
BLKCK
30
N.C.
31
CD_MDATA
32
STAT
33
CD_MCLK
34
USB_SDA
I/O
35
CD_MLD
36
USB_SCL
37
VDD18
38
MUTEA
39
VSS
I/O
Function
I
Motor Driver Input
I
Turntable Motor Drive Signal
("L":ON)
I
Motor Drive (1) Input
-
Traverse Motor Drive Signal
("L"): ON)
-
No Connection
-
Ground Connection (1) for Drive
-
Power Supply (1) for Drive
O
Motor Drive (1) reverse - action
output
O
Motor Drive (1) forward - action
output
O
Motor Drive (2) reverse - action
output
O
Motor Drive (2) forward - action
output
Function
O
Power Control Output 1(Pwr
Sply,Active HIGH)
O
Power Control Output 2
-
No Connection
O
FL Data Output / On Chip
Debugger Data
O
USB Reset Pin
O
FL CLK Output / On Chip
Debugger Clock
I
USB Interrupt Request
-
No Connection
-
No Connection
-
No Connection
-
Memory mode selection
(Ground connection)
O
Main Oscillator output (8MHz)
I
Main Oscillator input (8MHz)
-
Micom GND
I
Slow Oscillator input (32KHz)
O
Slow Oscillator output (32KHz)
-
Voltage supply 3.3V
-
Connect to pin 37
I
MICOM RESET PIN (L: reset)
-
No Connection
O
Switching Mode
I
Time out error
O
Verify error
-
No Connection
I
Remote Control Input
I
AC Failure Detect Signal
-
No Connection
-
No Connection
I
CD Subcode Block Clock Input
-
No Connection
O
CD LSI Command Data
I
CD LSI Status Input
O
CD LSI Command Clock
USB I2C Data Line
O
CD LSI Command Load
I
USB I2C Clock Line
-
Power Supply (1.8V)
O
Analog MUTE Output(L:MUTE
ON)
-
Micom GND
Pin No.
Mark
15
D3-
16
D3+
17
D4-
18
D4+
19
PVCC2
20
PGND2
21-24
N.C.
25
VCC
26
VREF
27
IN4
28
IN3
Pin No.
Mark
40
ASP_CLK
41
ASP_DATA
42
N.C.
43
N.C.
44
N.C.
45
CD_RST
46
N.C.
47
DEMO_SET
48
MODEL_SEL
49
TU_STEREO
50
TU_SDA
51
TU_CLK
52
VOL_JOG1
53
VOL_JOG2
54
TU_TUNED
55
N.C.
56
N.C.
57
N.C.
58
N.C.
59
N.C.
60
N.C.
61
N.C.
62
CRTIMER
63
VSS
64
FL_STROBE
65
CLOSE_L
66
OPEN_H
67
DAB_RST
68
DAB_ TU_RST
69
DAB_ TU_SCL
70
DAB_ TU_SDA
71
N.C.
72
DAB_RX
73
RDS_DATA
74
RDS_CLK
75
DAB_MODE
76
UART_IN
77
UART_OUT
81
SA-PM45E / SA-PM45EG / SA-PM45EE
I/O
Function
O
Motor Drive (3) reverse - action
output
O
Motor Drive (3) forward - action
output
O
Motor Drive (4) reverse - action
output
O
Motor Drive (4) forward - action
output
-
Power Supply (2) for Driver
-
Ground Connection (2) for Driver
-
No Connection
I
Power Supply terminal
I
Reference Voltage Input
I
Motor Driver (4) Input
I
Motor Driver (3) Input
I/O
Function
O
ASP Sound Processor Serial
Clock Output
O
ASP Sound Processor Serial
Data Output
-
No Connection
-
No Connection
-
No Connection
O
CD LSI Reset Ouput (L: reset)
-
No Connection
I
Demo Mode Setting Input
I
D-Port Select (H: D-Port, L:
Deck)
I/O
Tuner Stereo Signal
I/O
IIC Serial Data for Tuner (PLL
Data I/O)
O
IIC Serial Clock for Tuner (PLL
Clock Output)
I
Jog Input 1
I
Jog Input 2
I/O
Tuner Tuned Signal
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
I/O
CR TIMER
-
Micom GND
O
Chip select for FL Panel
O
CD Tray Close Control (Active
L)
O
CD Tray Open Control (Active
H)
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
I
RDS Data Input
I
RDS Clock Input
-
No Connection
-
No Connection
-
No Connection
Advertisement
Table of Contents
