Hi-Res. B/W camera instruction manual ADC 660N ADC 660P Version: Rev. A Part Number 8200-0839-01...
Page 2
Notice To prevent fire or shock hazard, do not expose the unit to rain or WARNING moisture. The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage"...
Page 3
Caution This installation should be made by a qualified service person and should conform to all local and national electrical and mechanical codes.
Page 4
PRECAUTIONS 1. Do not attempt to disassemble the camera. In order to prevent electric shock, do not remove screws or cover. There are no user-serviceable parts inside. 2. Do not expose the camera to rain or moisture, or try to operate it in wet areas.
II. EXAMPLES OF CONNECTIONS ... 17 IMPLEST NE MONITOR SYSTEM WITH ONE CAMERA NE MONITOR SYSTEM WITH TWO OR MORE CAMERAS III. DIMENSIONS... 18 IV. SPECIFICATIONS ... 19 ADC 660N and ADC 660P (BNC)... 7 ) ... 7 SCREW TERMINAL VIDEO D RIVE DC D ...
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ I. CONNECTORS AND CONTROLS 1. Video Output Connector (BNC) 1.0V p-p/75Ω composite video signal is provided at this connector. 2. Power Input Connector (screw terminal)
When using a VIDEO drive lens, the ALC/ELC DIP #1 must be set to the ALC (OFF) position. 4. Auto Iris Lens Connector for DC Drive Lens This connector supplies the control signals to the DC drive Auto Iris lens. ADC 660N and ADC 660P Signal GROUND POWER SUPPLY (9 VDC, 40mA)
This function can be used with either the linear shutter (EE or ELC mode) or an Auto Iris lens (AI lens or ALC mode). WITH BLC OFF ADC 660N and ADC 660P WITH BLC ON...
Fixed iris or manual iris lenses may be used with the linear shutter (EE/ELC mode) where the scene brightness varies over a limited range. Do not use the EE/ELC mode when an Auto Iris lens is installed. ADC 660N and ADC 660P...
Before making any adjustment, confirm that cameras A and B are connected to the power supply with the same polarity. To make an adjustment, follow the steps below. ADC 660N and ADC 660P ⑩...
Page 12
If an oscilloscope is not available, a less accurate adjustment can be made by observing the monitor and adjusting the V-phase control potentiometer until no roll occurs on the monitor when switching back and forth between cameras A and B. ADC 660N and ADC 660P Camera A's VIDEO OUT Camera B's VIDEO OUT...
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ 11. ALC Level Adjustment Potentiometer for DC Drive Lens This potentiometer is used only if the camera is fitted with a DC drive Auto Iris lens. It is used to control the amount of light striking the CCD image sensor.
Repeat steps 1 and 2 until the image remains sharp through the entire zoom range without having to make any focus adjustments. This completes the adjustment. The back-focus adjustment screw is held in place by friction, so there is no locking screw. ADC 660N and ADC 660P LEVEL Control Direction Clockwise Counterclockwise...
Page 15
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________...
Then screw the C-mount lens into the adaptor. 15. CCD Dust Protective Cap Remove this cap before installing the lens. Do not handle or leave the camera with cap open. 16. Camera Mount Hole 17. Camera Mount Base ADC 660N and ADC 660P...
Hi-Res. B/W camera instruction manual ADC 660N and ADC 660P _________________________________ II. EXAMPLES OF CONNECTIONS 1. Simplest: One monitor system with one camera 2. One monitor system with two or more cameras...
LENS MOUNT AUTO IRIS SUPPORT POWER REQUIREMENT OPERATION CONDITION NET WEIGHT (WITHOUT LENS) DIMENSIONS (W x H x L) ADC 660N and ADC 660P ADC660N 768(H) X 494(V) 1/3” INTERLINE TRANSFER CCD 2:1 INTERLACE INTERNAL/LINE LOCK SELECTABLE 580 TV LINE...