Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Related Manuals for IBASE Technology IB885
Summary of Contents for IBASE Technology IB885
- Page 1 IB885 AMD Sempron™ 200U/ 210U 3.5-inch Embedded Board USER’S MANUAL Version 1.0...
- Page 2 AMD Sempron™ 200U/210U are registered trademarks of AMD Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners. IB885 User’s Manual...
-
Page 3: Table Of Contents
IB885 Specifications ............3 Board Dimensions ............... 4 Installations ............5 Installing the Memory ............6 Setting the Jumpers ............. 7 Connectors on IB885 ............11 BIOS Setup ............21 Drivers Installation ........39 SM Bus Controller Driver Installation ......40 VGA Drivers Installation .......... - Page 4 This page is intentionally left blank. IB885 User’s Manual...
-
Page 5: Introduction
The M690E integrates an ATi Radeon X1200-based graphics engine supporting dual display, an LVDS interface, an integrated TMDS controller, and operates at core speeds of up to 400 MHz. IB885 features a low-power design, is validated with the AMD Sempron™. With one DDR2 800MHz SODIMM socket on board, the board supports up to 2GB of DDR2 system memory. -
Page 6: Checklist
INTRODUCTION Checklist Your IB885 package should include the items listed below. • The IB885 embedded board • This User’s Manual • 1 CD containing chipset drivers and flash memory utility • Cables and heatsink (shown below) is optional. IB885 User’s Manual... -
Page 7: Ib885 Specifications
Chipset built-in audio w/ ALC662 codec for 5.1CH Others 12V DC-in, DC backlight control, smart battery interface Mechanical and Environmental Dimensions 102mm x 148mm (4” x 5.8”) Operating Temperature 0°C~60°C (32°F~140°F) Storage Temperature -20°C~80°C (-4°F~176°F) Relative Humidity 10%~90% (non-condensing) IB885 User’s Manual... -
Page 8: Board Dimensions
INTRODUCTION Board Dimensions Top View IB885 User’s Manual... -
Page 9: Installations
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the IB885 in order to set up a workable system. The topics covered are: Installing the Memory ................6 Setting the Jumpers ................7 Connectors on IB885 ................11... -
Page 10: Installing The Memory
INSTALLATIONS Installing the Memory The IB885 board supports one DDR2 memory socket that can support up to 2GB memory, DDR2 400/533/667 (w/o ECC function). Installing and Removing Memory Modules To install the DDR2 modules, locate the memory slot on the board and perform the following steps: 1. -
Page 11: Setting The Jumpers
INSTALLATIONS Setting the Jumpers Jumpers are used on IB885 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on IB885 and their respective functions. -
Page 12: Jumper Locations On Ib885
INSTALLATIONS Jumper Locations on IB885 Jumpers on IB885 ................Page JP1, JP2, JP3: RS232/422/485 (COM2) Selection ........ 9 JBAT1: Clear CMOS Setting..............9 JP4: ATX or AT Power Selection ............9 JP5: CompactFlash Slave/Master Selection ......... 10 JP6: LCD Panel Power Selection ............10... -
Page 13: Jp1, Jp2, Jp3: Rs232/422/485 (Com2) Selection
COM2 is jumper selectable for RS-232, RS-422 and RS-485. Pin # Signal Name RS-232 R2-422 RS-485 DATA- DATA+ Ground Ground Ground JBAT1: Clear CMOS Setting JBAT1 Setting Normal Clear CMOS JP4: ATX or AT Power Selection ATX Power IB885 User’s Manual... -
Page 14: Jp5: Compactflash Slave/Master Selection
INSTALLATIONS JP5: CompactFlash Slave/Master Selection CF Setting Master Slave JP6: LCD Panel Power Selection LCD Panel Power 3.3V IB885 User’s Manual... -
Page 15: Connectors On Ib885
INSTALLATIONS Connectors on IB885 Connector Locations on IB885 ............12 CN9: PS/2 Keyboard/Mouse Connector ..........13 CN5, CN6: USB2/3 Ports ..............13 U16, U17: GbE RJ45 Ports ..............13 CN8: DVI-D Connector ..............13 CN7, J11: DC-IN 12V Power Connector ..........13 FAN1: System Fan Power Connector .......... -
Page 16: Connector Locations On Ib885
INSTALLATIONS Connector Locations on IB885 Connector Locations on IB885 CN9: PS/2 Keyboard/Mouse Connector ....................13 CN5, CN6: USB2/3 Ports ........................13 U16, U17: GbE RJ45 Ports ........................13 CN8: DVI-D Connector .......................... 13 CN7, J11: DC-IN 12V Power Connector ....................13 FAN1: System Fan Power Connector ..................... -
Page 17: Cn9: Ps/2 Keyboard/Mouse Connector
DATA 1- CLOCK + DATA 1+ N.C. SHIELD 1/3 N.C. DATA 3- N.C. DATA 3+ N.C. DDC POWER N.C. A GROUND 1 N.C. CN7, J11: DC-IN 12V Power Connector Pin # Signal Name DC in (12V only) Ground IB885 User’s Manual... -
Page 18: Fan1: System Fan Power Connector
Host data 15 Ground DRQ0 Ground Host IOW Ground Host IOR Ground IOCHRDY Host ALE DACK0 Ground IRQ14 No connect Address 1 No connect Address 0 Address 2 Chip select 0 Chip select 1 Activity Ground Ground N.C. IB885 User’s Manual... -
Page 19: Lvds1, Lvds2: Lvds Connectors (1St/2Nd Channel)
*JP6 can be used to set 3.3V or 5V. SATA1: SATA Connector CN1: HDD Power Connector Pin # Signal Name Ground Ground +12V CN2: VGA Connector (DF11 Connector) Signal Name Signal Name Ground Green Blue DDCDATA H_SYNC V_SYNC DDCCLK N.C. IB885 User’s Manual... -
Page 20: Cn3: Smart Battery Interface Connector
Data set ready Data carrier detect RTS1 RXD1 Request to send Receive data CTS1 TXD1 Clear to send Transmit data DTR1 Ringing indicator Data terminal ready Not used Ground DSR2 DCD2 RTS2 RXD2 CTS2 TXD2 DTR2 Not used Ground IB885 User’s Manual... -
Page 21: J2: Digital I/O
ID394 with Fintek F81216, 2 or 4 Serial Ports ID395 Winbond WPCT200 x1 for TPM1.2 ID395 Winbond WPCT200 for TPM1.2 CN1: LPC I/F connectors Package list Nylon Nut x1; Screw x2; Washer x2 ID394 LPC Serial Ports Adaptor Card IB885 User’s Manual... -
Page 22: J6: System Function Connector
This 2-pin connector is an “ATX Power Supply On/Off Switch” on the system that connects to the power switch on the case. When pressed, the power switch will force the system to power on. When pressed again, it will force the system to power off. IB885 User’s Manual... -
Page 23: J7: Cf Socket
LINEOUT L Ground JD FRONT LINEIN R LINEIN Ground JD LINEIN MIC-In MIC L Ground JD MIC1 J13: USB0/USB1 Connector Signal Name Signal Name Ground Ground Note: This USB connector is compatible with USB 2.0 devices only. IB885 User’s Manual... - Page 24 INSTALLATIONS This page is intentionally left blank. IB885 User’s Manual...
-
Page 25: Bios Setup
PNP/PCI Configurations .............. 34 PC Health Status ................35 Frequency/Voltage Control ............36 Load Fail-Safe Defaults ..............37 Load Optimized Defaults ............. 37 Set Supervisor/User Password ............37 Save & Exit Setup ................ 37 Exit Without Saving ..............37 IB885 User’s Manual... -
Page 26: Bios Introduction
<PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc> to quit. When you enter the Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices. IB885 User’s Manual... - Page 27 These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could cause the system to become unstable and crash in some cases. IB885 User’s Manual...
-
Page 28: Standard Cmos Setup
The following describes each item of this menu. Date The date format is: Day : Sun to Sat Month : 1 to 12 Date : 1 to 31 Year : 1999 to 2099 IB885 User’s Manual... - Page 29 The system boot will not be halted for a disk error; it will stop for all other errors. All, But Disk/Key The system boot will not be halted for a key- board or disk error; it will stop for all others. IB885 User’s Manual...
-
Page 30: Advanced Bios Features
When the CPU requests data, the system transfers the requested data from the main DRAM into cache memory, for even faster access by the CPU. These allow you to enable (speed up memory access) or disable the cache function. IB885 User’s Manual... - Page 31 Settings are from 6 to 30 characters per second. Typematic Delay (Msec) When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec. IB885 User’s Manual...
- Page 32 This option allows the system to access greater than 64MB of DRAM memory when used with OS/2 that depends on certain BIOS calls to access memory. The default setting is Non-OS/2. HDD S.M.A.R.T. Capability By default, this field is disabled. IB885 User’s Manual...
-
Page 33: Advanced Chipset Features
Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. The first screen shows three main items for user to select. Once an item selected, a submenu appears. Details follow. IB885 User’s Manual... -
Page 34: Integrated Peripherals
Primary Slave PIO Auto Primary Master UDMA Primary Slave UDMA Auto Phoenix - AwardBIOS CMOS Setup Utility South OnChip PCI Device Auto ITEM HELP HD Azalia Audio Enabled OnChip SATA Controller Native IDE Menu Level > OnChip SATA Type IB885 User’s Manual... - Page 35 The default values for these ports are: Serial Port 1 3F8/IRQ4 Serial Port 2 2F8/IRQ3 PWRON After PWR-Fail This field sets the system power status whether on or off when power returns to the system from a power failure situation. IB885 User’s Manual...
-
Page 36: Power Management Setup
DPMS Allows BIOS to control the video display. Blank Screen Writes blanks to the video buffer. Modem Use IRQ This field sets the IRQ used by the Modem. By default, the setting is 3. IB885 User’s Manual... - Page 37 Vista. It can produce periodic interrupts at a much higher resolution than the RTC and is often used to synchronize multimedia streams, providing smooth playback and reducing the need to use other timestamp calculations such as an x86 CPU’s RDTSC instruction. IB885 User’s Manual...
-
Page 38: Pnp/Pci Configurations
The default value is Enabled PCI Latency PCI latency refers to the number of cycles that any device can hold an IRQ before it is disconnected. Maximum Payload Size The default setting of the PCI Express Maximum Payload Size is 4096. IB885 User’s Manual... -
Page 39: Pc Health Status
PC health status. 1st / 2nd Smart Fan Temperature This field enables or disables the smart fan feature. At a certain temperature, the fan starts turning. Once the temperature drops to a certain level, it stops turning again. IB885 User’s Manual... -
Page 40: Frequency/Voltage Control
Menu Level > CPU Host/SRTC/ATIG Spread Spectrum This field sets the value of the spread spectrum. The default setting is Disabled. This field is for CE testing use only CPU Host/SRC/ATIG This field is set to Default. IB885 User’s Manual... -
Page 41: Load Fail-Safe Defaults
Select this option to exit the Setup utility without saving the changes you have made in this session. Typing “Y” will quit the Setup utility without saving the modifications. Typing “N” will return you to Setup utility. IB885 User’s Manual... - Page 42 BIOS SETUP This page is intentionally left blank. IB885 User’s Manual...
-
Page 43: Drivers Installation
The contents of this section include the following: SM Bus Controller Driver Installation ........40 VGA Drivers Installation ............43 Realtek Codec Audio Driver Installation ........45 LAN Drivers Installation ............46 IB885 User’s Manual... -
Page 44: Sm Bus Controller Driver Installation
1. In your Windows operating system, go to the Device Manager. 2. Double click SM Bus Controller which is under Other devices as shown in the picture below to go to the SM Bus Controller Properties window. IB885 User’s Manual... - Page 45 DRIVERS INSTALLATION 3. Under the SM Bus Controller Properties window, click the Driver tab and click Update Driver. 4. When the welcome screen of the Hardware Update Wizard appears, click No, not this time, and Next to continue. IB885 User’s Manual...
- Page 46 6. Select Search for the best driver in these locations., and enter the path where the drivers are located. If E:\ is your CD ROM drive, enter E:\Ali\AMD690T\SMBUS or click Browse to search for the path. 7. When driver installation is complete, click Finish for changes to take effect. IB885 User’s Manual...
-
Page 47: Vga Drivers Installation
1. Insert the CD that comes with the board. Click AMD M690T/E Chipset Drivers. 2. Click ATI Radeon X1200 Serial Graphics Drivers as shown below. Remarks: Before installing this driver, you have to install Microsoft NET Framework 2.0. Please go the Microsoft website to do this. IB885 User’s Manual... - Page 48 Recommended, in selecting the component that you want to install. 5. When the message regarding Windows Logo testing appears, click Continue Anyway to proceed with the driver installation. 6. Setup is now complete. Click Finish to restart the computer and for changes to take effect. IB885 User’s Manual...
-
Page 49: Realtek Codec Audio Driver Installation
1. Insert the CD that comes with the board. Click AMD M690T/E Chipset Drivers. 2. Click Realtek High Definition Codec Audio Driver. 3. In the Welcome screen, click Next to continue. After the driver installation, click Finish on the next screen to restart the computer. IB885 User’s Manual... -
Page 50: Lan Drivers Installation
1. Insert the CD that comes with the motherboard. Click LAN Card on the left side and click Realtek GbE_FE Ethernet PCI-E NIC Driver. 2. When the Welcome screen of the InstallShield Wizard appears, click Next to continue. IB885 User’s Manual... - Page 51 DRIVERS INSTALLATION 3. On the next screen, you are asked to click Install to begin the installtion process. Now, click Install to proceed. 4. Installation is now complete, click Finish to exit the InstallShield Wizard. IB885 User’s Manual...
- Page 52 DRIVER INSTALLATION This page is intentionally left blank. IB885 User’s Manual...
-
Page 53: Appendix
Parallel Port #1(LPT1) 360 - 36F Network Ports 3B0 - 3BF Monochrome & Printer adapter 3C0 - 3CF EGA adapter 3D0 - 3DF CGA adapter 3F0h - 3F7h Floppy Disk Controller 3F8h - 3FFh Serial Port #1(COM1) IB885 User’s Manual... -
Page 54: Interrupt Request Lines (Irq)
Serial Port #2 IRQ4 Serial Port #1 IRQ5 Reserved IRQ6 Floppy Disk Controller IRQ7 Parallel Port #1 IRQ8 Real Time Clock IRQ9 Reserved IRQ10 Reserved IRQ11 Reserved IRQ12 PS/2 Mouse IRQ13 80287 IRQ14 Primary IDE IRQ15 Secondary IDE IB885 User’s Manual... -
Page 55: Watchdog Timer Configuration
(argc != 2) printf(" Parameter incorrect!!\n"); return 1; if (Init_W627EHF() == 0) printf(" Winbond 83627HF is not detected, program abort.\n"); return 1; bTime = strtol (argv[1], endptr, 10); printf("System will reset after %d seconds\n", bTime); EnableWDT(bTime); return 0; //=========================================================================== IB885 User’s Manual... - Page 56 = Get_W627EHF_Reg( 0xF5); bBuf &= (!0x08); Set_W627EHF_Reg( 0xF5, bBuf); //count mode is second Set_W627EHF_Reg( 0xF6, interval); //set timer //=========================================================================== void DisableWDT(void) Set_W627EHF_LD(0x08); //switch to logic device 8 Set_W627EHF_Reg(0xF6, 0x00); //clear watchdog timer Set_W627EHF_Reg(0x30, 0x00); //watchdog disabled //=========================================================================== IB885 User’s Manual...
- Page 57 Init_Finish; W627EHF_BASE = 0x00; result = W627EHF_BASE; Init_Finish: return (result); //=========================================================================== void Unlock_W627EHF (void) outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK); outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK); //=========================================================================== void Lock_W627EHF (void) outportb(W627EHF_INDEX_PORT, W627EHF_LOCK); //=========================================================================== void Set_W627EHF_LD( unsigned char LD) Unlock_W627EHF(); outportb(W627EHF_INDEX_PORT, W627EHF_REG_LD); outportb(W627EHF_DATA_PORT, LD); Lock_W627EHF(); IB885 User’s Manual...
- Page 58 (W627EHF_BASE) #define W627EHF_DATA_PORT (W627EHF_BASE+1) //=========================================================================== #define W627EHF_REG_LD 0x07 //=========================================================================== #define W627EHF_UNLOCK 0x87 #define W627EHF_LOCK 0xAA //=========================================================================== unsigned int Init_W627EHF(void); void Set_W627EHF_LD( unsigned char); void Set_W627EHF_Reg( unsigned char, unsigned char); unsigned char Get_W627EHF_Reg( unsigned char); //=========================================================================== #endif //__W627EHF_H IB885 User’s Manual...