Page 1
Manual iBASE IB811 The information contained in this document has been carefully researched and is, to the best of our knowledge, accurate. However, we assume no liability for any product failures or damages, immediate or consequential, resulting from the use of the information provided herein. Our products are not intended for use in systems in which failures of product could result in personal injury.
Page 3
No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
Compliance This product has passed CE tests for environmental specifications and limits. This product is in accordance with the directives of the European Union (EU). In a domestic environment, this product may cause radio interference in which case users may be required to take adequate measures.
Important Safety Information Carefully read the precautions before using the board. Environmental conditions: Use this product in environments with ambient temperatures between 0˚C and 60˚C, or -40 and 85 ˚C. Do not leave this product in an environment where the storage temperature may be below -40°...
Warranty Policy IBASE standard products: 24-month (2-year) warranty from the date of shipment. If the date of shipment cannot be ascertained, the product serial numbers can be used to determine the approximate shipping date. -party parts: 12-month (1-year) warranty from delivery for the 3 -party parts that are not manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices, power adapter, panel and touchscreen.
Table of Contents Compliance ..................iii Important Safety Information ............iv Warranty Policy ................v Technical Support & Services ............v Chapter 1 General Information ..........1 Introduction ..................2 Features ....................2 Packing List ..................3 Optional Accessories ................3 Specifications ..................
Chapter 1 General Information The information provided in this chapter includes: Features Packing List Block Diagram Specifications Board Overview Board Dimensions...
Introduction IB811F is a 3.5” disk-size single board computer based on the platform of ® ® ® Intel Atom™ x7/x5, Pentium or Celeron . It features both DisplayPort and HDMI at coastline, and on-board headers for eDP / 24-bit dual channel LVDS interfaces for video display.
General Information Packing List Your IB811F package should include the items listed below. If any of the items below is missing, contact the distributor or dealer from whom you purchased the product. IB811F SBC Disk (including chipset drivers and flash memory utility) ...
Specifications Product IB811F-I50 IB811F-I30 IB811F-420 IB811F-335 Name 3.5” disk-size SBC Form Factor System Windows 10 Enterprise (64-bit) Operating Windows 10 IoT Core (64-bit) System Linux Ubuntu ® ® Intel Intel ® ® Intel Intel ® ® CPU Type Atom™...
Page 14
General Information Product IB811F-I50 IB811F-I30 IB811F-420 IB811F-335 Name EuP/ErP Smart Power failure detection by a jumper connector Control LVDS brightness control 102.22 x 147.01 mm (4.02” x 5.8”) Dimensions RoHS Certification CE, FCC Class B, LVD I/O Ports ...
Page 15
Product IB811F-I50 IB811F-I30 IB811F-420 IB811F-335 Name Environment Operation: -40 ~ 85 °C Operation: 0 ~ 60 °C (-40 ~ 185 °F) (32 ~ 140 °F) Temperature Storage: -40 ~ 110 °C Storage: -40 ~ 110 °C (-40 ~ 230 °F) (-40 ~ 230 °F) Relative...
Overview Top View Bottom View Photo of IB811F-420 *The photos above are for reference only. Some minor components may differ. IB811F Series User’s Manual...
Page 18
General Information I/O View Name Name COM1 (RJ10) Port LAN Port DisplayPort USB 3.0 Port HDMI Port IB811F Series User’s Manual...
Chapter 2 Hardware Configuration This section provides information on jumper settings and connectors on the IB811F in order to set up a workable system. On top of that, you will also need to install crucial pieces such as the CPU and the memory before using the product. The topics covered are: ...
Essential Installations Before You Begin Follow the instructions below to install the memory. 2.1.1 Installing the Memory The IB811F board supports two DDR3L memory sockets for a maximum total memory of 8 GB. To install the modules, locate the memory slot on the board and perform the following steps: Align the key of the memory module with that on the memory slot and insert the module slantwise.
Hardware Configuration Setting the Jumpers Set up and configure your IB811F by using jumpers for various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your use. 2.2.1 How to Set Jumpers Jumpers are short-length conductors consisting of several metal pins with a non-conductive base mounted on the circuit board.
Hardware Configuration Jumpers Quick Reference Function Jumper Name Page LCD Panel Brightness Selection LVDS Planel Power Selection eDP Panel Power Selection eDP / LVDS Panel Seelction ATX / AT Power Selection CMOS Data Clearance ME Register Clearance Factory Use Only 2.4.1 LVDS Panel Brightness Selection (JP1) Function...
2.4.6 CMOS Data Clearance (JP6) Function Pin closed Illustration Normal (default) Clear CMOS 2.4.7 ME Register Clearance (JP7) Function Pin closed Illustration Normal (default) Clear ME IB811F Series User’s Manual...
Hardware Configuration Connectors Quick Reference Function Connector Name Page eDP Connector CN2 (shared with M.2 B-key) SATA III Connector CN3 (shared with mSATA) LAN Ports USB 3.0 Ports CN5, CN6 Console COM1 (RJ10) RS-232/422/485 Port DisplayPort HDMI Port LCD Backlight Connector LVDS Connector J1, J3 Audio Connector...
Hardware Configuration 2.5.2 SATA III Connector (CN2, CN3) CN2: shared with M.2 B-key CN3: shared with mSATA 2.5.3 LAN Ports (CN4) 2.5.4 USB 3.0 Ports (CN5, CN6) IB811F Series User’s Manual...
2.5.5 Console COM1 (RJ10) RS-232/422/485 Port (CN7) COM1 port is jumper-less and configurable in BIOS. Assignment Assignment DSR, Data set ready DCD, Data carrier detect Ground DTR, Data terminal ready Ground CTS, Clear to send TX, Transmit RTS, Request to send RX, Receive RI, Ring Indicator Assignment...
2.5.16 COM2 / COM3 / COM4 RS-232 Port (J16, J17, J12) Assignment Assignment DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready Ground DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator Not Used 2.5.17...
Hardware Configuration 2.5.18 Front Panel Connector (J13) Assignment Assignment Ground PWR_BTN 3.3V HDD Active Ground Reset Ground J13 is utilized for system indicators to provide light indication of the computer activities and switches to change the computer status. It provides interfaces for the following functions.
Introduction This section describes the installation procedures for software and drivers. The software and drivers are included with the motherboard. If you find anything missing, please contact the distributor where you made the purchase. The contents of this section include the following: Note: After installing your Windows operating system, you must install the ®...
Driver Installation ® Intel Chipset Software Installation Utility ® The Intel Chipset drivers should be installed first before the software drivers to install INF files for Plug & Play function for Intel chipset components. Follow the instructions below to complete the installation. Insert the disk enclosed in the package with the board.
Page 43
® When the Welcome screen to the Intel Chipset Device Software appears, click Next to continue. Click Yes to accept the software license agreement and proceed with the installation process. On the Readme File Information screen, click Install for installation. The driver has been completely installed.
Driver Installation VGA Driver Installation Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) Apollolake Graphics Driver. IB811F Series User’s Manual...
Page 45
When the Welcome screen appears, click Next to continue. Click Yes to accept the license agreement and click Next until the installation starts. The driver has been completely installed. You are suggested to restart the computer for changes to take effect. IB811F Series User’s Manual...
Driver Installation HD Audio Driver Installation Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Realtek High Definition Audio Driver. IB811F Series User’s Manual...
Page 47
On the Welcome screen of the InstallShield Wizard, click Next for installation. Click Next until the installation starts. The driver has been completely installed. You are suggested to restart the computer for changes to take effect. IB811F Series User’s Manual...
Driver Installation ® Intel Trusted Execution Engine Drivers Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) TXE Drivers. IB811F Series User’s Manual...
Page 49
When the Welcome screen appears, click Next. Accept the license agreement and click Next. Click Next for installation. As the driver has been sccessfully installed, you are suggested to restart the computer for changes to take effect. IB811F Series User’s Manual...
Driver Installation ® Intel Serial IO Drivers Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) Serial IO Drivers. IB811F Series User’s Manual...
Page 51
When the Welcome screen to the InstallShield Wizard appears, click Next. Accept the license agreement and click Next. After reading the Readme File Information, click Next for installation. As the driver has been sccessfully installed, you are suggested to restart the computer for changes to take effect. IB811F Series User’s Manual...
Driver Installation LAN Driver Installation Click LAN Card on the left pane and then Intel LAN Controller Drivers on the right pane. Click Intel(R) I21x Gigabit Network Drivers.. IB811F Series User’s Manual...
Page 53
When the Welcome screen appears, click Next. Accept the license agreement and click Next. On the Setup Options screen, click the checkbox to select the desired driver(s) for installation. Then click Next to continue. The wizard is ready for installation. Click Install. As the installation is complete, you are suggested to restart the computer for changes to take effect.
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: Main Settings Advanced Settings Chipset Settings Boot Settings ...
4.1 Introduction The BIOS (Basic Input/Output System) installed in the ROM of your ® computer system supports Intel processors. The BIOS provides critical low-level support for standard devices such as disk drives, serial ports and parallel ports. It also provides password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
Page 56
BIOS Setup When you enter the BIOS Setup utility, the Main Menu screen will appear on the screen. The Main Menu allows you to select from various setup functions and exit choices. Warning: It is strongly recommended that you avoid making any changes to the chipset defaults.
4.3 Main Settings BIOS Setting Description System Date Sets the date. Use the <Tab> key to switch between the data elements. System Time Set the time. Use the <Tab> key to switch between the data elements. IB811F Series User’s Manual...
BIOS Setup 4.4 Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. IB811F Series User’s Manual...
4.4.1 ACPI Computing BIOS Setting Description Enable Hibernation Enables / Disables the system ability to hibernate (OS/S4 Sleep State). This option may be not effective with some OS. ACPI Sleep State Selects an ACPI sleep state (Suspend Disabled or S3) where the system will enter when the Suspend button is pressed.
BIOS Setup 4.4.2 LVDS (eDP/DP) Configuration BIOS Setting Description LVDS (eDP/DP) Enables / Disables LVDS (eDP/DP) Support Panel Color Depth Selects a panel color depth as 18 or 24 (VESA or JEIDA) bit. LVDS Channel Type Sets the LVDS channel type as single or dual channel.
4.4.3 F81866 Super IO Configuration BIOS Setting Description Standby Power on S5 Enables / Disables to provide the standby power for devices. Options: All Enable / Enable Ethernet for WOL / All Disable Serial Ports Sets parameters of serial ports. Configuration Enables / Disables the serial port and select an optimal setting for the Super IO device.
Page 62
BIOS Setup 4.4.3.1. Serial Port 1 Configuration BIOS Setting Description Serial Port Enables / Disables the serial port. Change Settings Selects an optimal settings for Super IO device. Options: Auto IO = 3F8h; IRQ = 4 IO = 3F8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 ...
4.4.4 Fintek Super IO Hardware Monitor BIOS Setting Description Temperatures / These fields are the parameters of the hardware Voltages monitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status. CPU Shutdown Sets a threshold of temperature to shut down if Temperature...
4.4.6 CPU Configuration BIOS Setting Description Socket 0 CPU Displays the socket specific CPU information. Information CPU Power Allows you to enable / disable Turbo Mode. Management Active Processor Enables / Disables the cores in the processor Cores package. Monitor Mwait Enables / Disables Monitor Mwait.
BIOS Setup 4.4.9 CMS Configuration BIOS Setting Description CSM Support Enables / Disables CSM support. GateA20 Active Upon Request disables GA20 when using BIOS services. Always cannot disable GA20, but is useful when any RT code is executed above 1 MB. INT19 Trap Response Sets how BIOS reacts on INT19 trap by Option ROM.
4.4.10 USB Configuration BIOS Setting Description Legacy USB Support Enabled enables Legacy USB support. Auto disables legacy support if there is no USB device connected. Disabled keeps USB devices available only for EFI applications. XHCI Hand-off This is a workaround for OSes without XHCI hand-off support.
BIOS Setup 4.5 Chipset Settings 4.5.1 North Bridge BIOS Setting Description Max TOLUD Sets a maximum value of TOLUD. Options: 2 / 2.25 / 2.5 / 2.75 / 3 GB IB811F Series User’s Manual...
4.5.2 South Cluster Configuration 4.5.2.1. HD Audio Configuration IB811F Series User’s Manual...
Page 72
BIOS Setup 4.5.2.2. PCI Express Configuration BIOS Setting Description PCI Express Root Accesses the control of the PCI Express Root Port 1 ~ 6 Port. IB811F Series User’s Manual...
Page 73
BIOS Setting Description PCI Express Root Enables/ Disables the PCIe root port. Port Auto: To disable unused root port automatically for the most optimum power savings. ASPM Sets the PCIe active state power management. Options: Disable / L0s / L1 / L0SL1 / Auto L1 Substates Sets PCIe L1 substates.
Page 74
BIOS Setup 4.5.2.3. SATA Drivers BIOS Setting Description Chipset SATA Enables / Disables the Chipset SATA Controller. The Chipset SATA Controller supports the 2 black internal SATA ports (up to 3Gb/s supported per port). SATA Mode Selection Determines how SATA controller(s) operate. IB811F Series User’s Manual...
Page 75
4.5.2.4. USB Configuration BIOS Setting Description XHCI Pre-Boot Driver Enables / Disables the support for XHCI Pre-Boot Driver. XHCI Mode Enables / Disables XHCI mode. If disabled, XHCI controller would be disabled, and none of the USB devices are detectable or usable when systen is booted up in OS.
BIOS Setup 4.6 Security Settings BIOS Setting Description Setup Administrator Sets an administrator password for the setup Password utility. User Password Sets a user password. IB811F Series User’s Manual...
BIOS Setup 4.8 Save & Exit Settings BIOS Setting Description Save Changes and Exits system setup after saving the changes. Exit Discard Changes and Exits system setup without saving any changes. Exit Save Changes and Resets the system after saving the changes. Reset Discard Changes and Resets system setup without saving any...
Appendix I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used. Address Device Description 0x00000A00-0x00000A0F Motherboard resources 0x00000A10-0x00000A1F Motherboard resources...
Page 81
Address Device Description 0x000003F8-0x000003FF Communications Port (COM1) 0x000002F8-0x000002FF Communications Port (COM2) 0x000003E8-0x000003EF Communications Port (COM3) 0x000002E8-0x000002EF Communications Port (COM4) 0x0000E000-0x0000EFFF Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port - 5AD8 0x00000000-0x0000006F PCI Express Root Complex 0x00000078-0x00000CF7 PCI Express Root Complex 0x00000D00-0x0000FFFF PCI Express Root Complex 0x00000020-0x00000021 Programmable interrupt controller...
Page 82
Appendix Address Device Description 0x0000F090-0x0000F097 Standard SATA AHCI Controller 0x0000F080-0x0000F083 Standard SATA AHCI Controller 0x0000F060-0x0000F07F Standard SATA AHCI Controller 0x00000040-0x00000043 System timer 0x00000050-0x00000053 System timer IB811F Series User’s Manual...
Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board. Level Function IRQ 0 System timer IRQ 3 Communications Port (COM2) IRQ 4 Communications Port (COM1) IRQ 4...
Page 84
Appendix Level Function IRQ 4294967280 ~ Intel(R) I211 Gigabit Network Connection #2 IRQ 4294967285 IRQ 4294967286 ~ Intel(R) I211 Gigabit Network Connection IRQ 4294967291 IRQ 4294967292 Intel(R) Trusted Execution Engine Interface IRQ 4294967293 Intel(R) HD Graphics IRQ 4294967294 Standard SATA AHCI Controller IB811F Series User’s Manual...
Watchdog Timer Configuration The Watchdog Timer (WDT) is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock.
Page 87
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. //--------------------------------------------------------------------------- #include "F81866.H" #include <dos.h>...
Page 88
Appendix //--------------------------------------------------------------------------- void Set_F81866_Reg( unsigned char REG, unsigned char DATA) Unlock_F81866(); outportb(F81866_INDEX_PORT, REG); outportb(F81866_DATA_PORT, DATA); Lock_F81866(); //--------------------------------------------------------------------------- unsigned char Get_F81866_Reg(unsigned char REG) unsigned char Result; Unlock_F81866(); outportb(F81866_INDEX_PORT, REG); Result = inportb(F81866_DATA_PORT); Lock_F81866(); return Result; //--------------------------------------------------------------------------- //--------------------------------------------------------------------------- // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE.
Page 89
Our company network supports you worldwide with offices in Germany, Austria, Switzerland, Great Britain and the USA. For more information please contact: Headquarters Germany FORTEC Elektronik AG Lechwiesenstr. 9 86899 Landsberg am Lech Phone: +49 8191 91172-0 E-Mail: sales@fortecag.de Internet: www.fortecag.de Fortec Group Members Austria...