Table of Contents
Advertisement
Quick Links
SmartRack
Copyright © 2008 Tripp Lite. All trademarks are the sole property of their respective owners.
Owner's Manual
™
Model: SRCABLELADDER
1111 W. 35th Street, Chicago, IL 60609 USA
+1.773.869.1234 • www.tripplite.com
Accessories
1
2
2
2
2
3
3
4
4
5
6
7
8
8
Advertisement
Table of Contents
Related Manuals for Tripp Lite SmartRack SRCABLELADDER
Summary of Contents for Tripp Lite SmartRack SRCABLELADDER
-
Page 1: Table Of Contents
3-5 Installation Within Row 3-6 Ground Connection 4 – Storage and Service 5 – Warranty and Warranty Registration Copyright © 2008 Tripp Lite. All trademarks are the sole property of their respective owners. Accessories ™ Model: SRCABLELADDER 1111 W. 35th Street, Chicago, IL 60609 USA... -
Page 2: Introduction
1 – Introduction SRCABLELADDER provides roof-mounted cable routing for Tripp Lite’s SmartRack Enclosures, allowing cable bundles to span aisles and/or spaces between enclosures in the same row. Note: Standard installation of SRCABLELADDER requires Tripp Lite’s SRCABLETRAY accessory, sold separately. 1-1 Parts List... -
Page 3: Installation
3 – Installation Note: Prior to installation, you must install the SRCABLETRAY accessory (sold separately) on each enclosure that will be linked by the SRCABLELADDER accessory. For ordering information, call Tripp Lite Customer Service at +1.773.869.1234. 3-1 Planning SRCABLELADDER can provide enclosure-to-enclosure cable routing across an aisle or within a single row. You can combine multiple SRCABLELADDER and SRCABLETRAY accessories to meet the cable routing needs of almost any configuration of SmartRack Enclosures, but planning and measurement are required to ensure a secure fit. Tripp Lite recommends that you read the entire manual in advance to gain a... -
Page 4: Ladder Modification (Optional)
3 – Installation (continued) 3-2 Ladder Modification (Optional) Warning: When using tools to cut or drill metal, use eye protection and follow all other safety precautions recommended by the tool manufacturer and required by applicable safety regulations. Use caution and wear safety gloves when handling metal parts that have been cut to length. -
Page 5: Installation Across Aisle
3 – Installation (continued) 3-4 Installation Across Aisle Note: Follow the instructions in this section only if the SRCABLELADDER accessory will be installed across an aisle. If the SRCABLELADDER accessory will be installed within a row of enclosures, follow the instructions in Section 3-5 Installation Within Row instead. Insert four assembly brackets into the ends of the ladder. -
Page 6: Installation Within Row
3 – Installation (continued) 3-5 Installation Within Row Note: Follow the instructions in this section only if the SRCABLELADDER accessory will be installed within a row of enclosures. If the SRCABLELADDER accessory will be installed across an aisle, follow the instructions in Section 3-4 Installation Across Aisle instead. Insert four assembly brackets in the open ends of the ladder, hooked end first. When the ladder is oriented so that the ladder’s... -
Page 7: Ground Connection
3 – Installation (continued) 3-5 Installation Within Row After inserting the clevis pins, insert a cotter pin hole at the end of each clevis pin. (The straight section of the cotter pin goes through the hole.) 3-6 Ground Connection After installing the SRCABLELADDER accessory, determine where to place ground brackets by noting the distance between one end of the ladder and the grounding post nearest SRCABLETRAY accessory. -
Page 8: Storage And Service
Storage The unit must be stored in a clean, secure environment with a temperature less than 40° C (104° F) and a relative humidity less than 90% (non-condensing). Store the unit in its original shipping container if possible. Service The unit is covered by the limited warranty described in this manual. For more information, call Tripp Lite Customer Service at +1.773.869.1234. 5 – Warranty and Warranty Registration Limited Warranty Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 5 years from the date of initial purchase. If the product should prove defective in material or workmanship within that period,...