Download Print this page

Tripp Lite SmartRack Panel-Mount Three-Fan Accessory SR14 Owner's Manual

Panel-mount three-fan accessory

Advertisement

Available languages

Available languages

Quick Links

SmartRack
Panel-Mount
Three-Fan Accessory

IMPORTANT SAFETY INSTRUCTIONS.

and use an assistant to lift and stabilize the unit during installation. Do not connect the fan panel to
power until it has been properly installed in a rack enclosure.
Rail
Clip Nuts
Figure 1
Installation Procedures
Parts List:
SR14 Panel-Mount Three-Fan Accessory (1)
#10-32 Clip Nuts—Tinnerman # C31758-1032-3B (4)
#10-32 x 1/2 Philips-Head Screws (4)
Tools Required: Phillips-Head Screwdriver
Note: The included clip nuts provide mounting points on
19-in. rackmount equipment rails. Clip nuts have a front
(screwhead) side. Before securing clip nuts to the rack,
determine which way they should face for ease of access to
the screwhead during component installation. Clip nuts may
be removed from rack rails by placing the tip of a fl at-blade
screwdriver or knife under the tab on the front and prying
up to free the retainer ring from the rail (see Figure 1).
1. Select the position at which the fan panel will be installed
in the rack enclosure.
2. Install one clip nut into the top hole of the selected
position
3. Install a second clip nut on the same rail, six holes down
(see Figure 2).
4. Measure from the bottom of the vertical rail to the top
clip nut. Install remaining clip nuts on the opposite
vertical rail at the measured height.
5. Using an assistant, attach the fan panel to the clip nuts with
the included 10-32 x 1/2 Phillips-head screws (see Figure
3). Plug the power cord into a grounded 120V outlet.
Copyright ©2007 Tripp Lite. All rights reserved. SmartRack™ is a trademark of Tripp Lite.
Owner's Manual
Model: SR14
Use this hole
Rail
Figure 2
To avoid injury, follow installation steps in sequence
.5"
.625"
.625"
.5"
.625"
.625"
.5"
10-32 x 1/2
Philips-Head Screws
.625"
.625"
.5"
Warranty Registration
Visit www.tripplite.com/warranty today to register the
warranty for your new Tripp Lite product. You'll be
automatically entered into a drawing for a chance to win a
FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply.
See website for details.
Tripp Lite follows a policy of continuous improvement.
Product specifi cations are subject to change without notice.
1111 W. 35th Street
Chicago, IL 60609 USA
Customer Support: (773) 869-1234
www.tripplite.com
Clip Nuts
Power Cord
Figure 3
Rails

Advertisement

loading

Summary of Contents for Tripp Lite SmartRack Panel-Mount Three-Fan Accessory SR14

  • Page 1: Important Safety Instructions

    5. Using an assistant, attach the fan panel to the clip nuts with the included 10-32 x 1/2 Phillips-head screws (see Figure 3). Plug the power cord into a grounded 120V outlet. Copyright ©2007 Tripp Lite. All rights reserved. SmartRack™ is a trademark of Tripp Lite. Owner’s Manual ™...
  • Page 2 1/2 Incluidos (Vea la Figura 3). Enchufe la clavija del cable de alimentación en una toma de corriente de 120V adecuadamente conectada a tierra. Tripp Lite tiene una política de mejoramiento continuo. Las especifi caciones están sujetas a cambio sin previo aviso. Para evitar lesiones, siga los pasos de...
  • Page 3 2. TRIPP LITE, se compromete a reparar, y en caso de que a su juicio no sea posible la reparación, a cambiar el equipo, así...
  • Page 4 écrous à déclic avec les vis Phillips 10-32 x 1/2 incluses (voir Figure 3). Brancher le cordon d’alimentation dans une prise mise à la terre, 120 V. La politique de Tripp Lite est celle d’une amélioration continuelle. Les spécifi cations peuvent être modifi ées sans préavis.