Denon AVR-1312 Getting Started page 12

ENGliSh ENGliSh DEutSch DEutSch
Speaker Config.
(Continued)
Surround Back Set the presence, size and
number of surround
speakers.
• Large : Use a large speaker that can adequately
play back low frequencies.
• Small : Use a small speaker that has inadequate
playback capacity for low frequencies.
• None : Select when the surround back speakers
are not connected.
Even when the "Surround Back" setting
is other than "None", sound may not be
emitted from the surround back speaker,
depending on the playback source. In this
case, make "Surround Parameter" – "SB CH
OUT" (vm page 38 "Adjusting the sound
field effects") setting other than "OFF".
Subwoofer Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
When "Front" is set to "Small", "Subwoofer"
is automatically set to "Yes".
5
Press ENTER to enter the setting.
Speaker Setup
Speaker Config. Front
Bass Setting Center
Distance Surround
Channel Level Surround Back
Crossover Freq. Subwoofer
[ENTER] Enter [ ] Return
6 6
FrANçAiS FrANçAiS itAliANo itAliANo
Bass Setting
1
ui
Use to select "Bass Setting", and
back
then press ENTER .
Speaker Setup
Speaker Config. LPF for LFE
Bass Setting SW Mode
Distance
Channel Level
Crossover Freq.
[ENTER] Enter [
Bass Setting
1
LPF for LFE 120Hz
SW Mode LFE
2
Use o p to select the frequency.
[ENTER] Enter [
LPF for LFE Set LFE signal playback range.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz /
200Hz / 250Hz
ESpAñol ESpAñol NEDErlANDS NEDErlANDS SVENSKA SVENSKA
Default settings are underlined.
3
ui
Use to select "SW Mode", and
use o p to select a detailed setting.
Bass Setting
1
LPF for LFE
SW Mode
SW Mode Select low range signals to be
reproduced by subwoofer.
] Return [ENTER] Enter
• LFE : The low range signal of the channel set to
"Small" speaker size is added to the LFE signal
output from the subwoofer.
• LFE+Main : The low range signal of all channels
is added to the LFE signal output from the
subwoofer.
• "SW Mode" can be set when "Speaker Config."
– "Subwoofer" (vpage 6) is set to "Yes".
• Play music or a movie source and select the
mode offering the strongest bass.
] Return
• Select "LFE+Main" if you want the bass signals
to always be produced from the subwoofer.
NOTE
If "Front" and "Center" for "Speaker Config."
are set to "Large", and "SW Mode" is set to
"LPF for LFE", no sound may be output from
the subwoofers, depending on the input signal or
selected surround mode.
4
ENTER
Press to enter the setting.
Speaker Setup
Speaker Config.
Bass Setting
Distance
Channel Level
Crossover Freq.
[ENTER] Enter
РУССКИЙ POLSKI
Distance
Default settings are underlined.
1
ui
Use to select "Distance", and
then press ENTER
Speaker Setup
120Hz Speaker Config.
LFE Bass Setting
Distance
Channel Level
Crossover Freq.
[ ] Return
Distance
1
Step
Front L
Front R
Center
Subwoofer
2
o p
Use to change the step (minimum
variable distance).
0.1m : For changing in 0.1-meter steps.
0.01m : For changing in 0.01-meter steps.
LPF for LFE
SW Mode
[ ] Return
TÜRKÇE
.
Step
Front L/R
Center
Subwoofer
Surround L/R
[ENTER] Enter [ ] Return
0.1m
3.60m
3.60m
3.60m
3.60m
[ENTER] Enter [ ] Return