Advertisement
Quick Links
INSTALLATION
INSTRUCTIONS
PARTS LIST
Left front illuminated door sill trim
Right front illuminated door sill trim
Left rear illuminated door sill trim
Right rear illuminated door sill trim
Door sill trim harness
Subharness
© 2019 American Honda Motor Co., Inc. – All Rights Reserved.
Accessory
ILLUMINATED DOOR
SILL TRIMS
P/N 08E12-TY2-200A
Fuse label
27 Wire ties
2
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Ratchet
10 mm Socket
10 mm Open end wrench
Diagonal cutters
Tape
Isopropyl alcohol
Shop towel
Scissors
The following tools are available through the Acura Tool
and Equipment Program. On the iN, click on: Service >
Service Bay > Tool and Equipment Program, then enter
the number under "Search." Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
• Plastic Trim Tool (T/N SILTRIMTL10)
BII12560-03 (1907)
Application
2020 RLX
Aluminum tapes
Publications No.
VERSION 1
Issue Date
JUL 2019
1 of 18
08E12-TY2-2000-9A
Advertisement
Related Manuals for Acura 08E12-TY2-200A
Summary of Contents for Acura 08E12-TY2-200A
- Page 1 Isopropyl alcohol Shop towel Scissors The following tools are available through the Acura Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.
-
Page 2: Installation
Illustration of the Illuminated Door Sill Trims in the Apply tape to the center console panel and the Vehicle driver’s and passenger’s console side trims as shown. If the vehicle has a shift lever, wrap a shop towel around the shift lever. RIGHT FRONT RIGHT REAR ILLUMINATED... - Page 3 Remove the center lower trim and unplug the vehicle Open the glove box. Pull away the door opening connectors. seal, and remove the passenger’s dashboard side lid. 3 CLIPS 4 CLIPS 3 HOOKS VEHICLE CENTER LOWER FRONT CONNECTORS TRIM DOOR OPENING Remove the center lower panel and unplug the PASSENGER’S...
- Page 4 10. Close the glove box. 12. Remove the two bolts from the bottom of the glove box. 11. Remove the passenger’s dashboard lower cover and unplug the vehicle connector. GLOVE BOX VEHICLE FRONT CONNECTOR 4 CLIPS 2 BOLTS FRONT PASSENGER’S DASHBOARD LOWER COVER 4 of 18...
- Page 5 13. Remove the glove box and unplug the vehicle 15. Pull away the door opening seal, and remove the connectors. passenger’s kick panel. 2 CLIPS DOOR OPENING SEAL VEHICLE (Pull away.) CONNECTORS 2 CLIPS PASSENGER’S KICK PANEL 16. Pull away the door opening seal, and remove the driver’s dashboard side lid.
- Page 6 17. Remove the driver’s dashboard lower cover. Unplug 18. Turn the knob, and remove the driver’s dashboard the vehicle connectors and aspirator hose, then under cover and unplug the vehicle connector. remove the plate. CLIP FRONT ASPIRATO VEHICLE 9 CLIPS R HOSE CONNECTORS DRIVER’S...
- Page 7 20. Pull away the door opening seal, and remove the 22. Remove the right rear door sill trim. driver’s kick panel. 4 CLIPS DOOR OPENING SEAL RETAINING 2 CLIPS (Pull away.) RIGHT REAR DOOR SILL TRIM FRONT 23. Remove the right center pillar lower trim. DRIVER’S KICK PANEL RETAINING...
- Page 8 25. Carefully remove the insulator from the driver’s front 27. Using isopropyl alcohol on a shop towel, thoroughly door sill trim. Do not damage the insulator. clean the left front illuminated door sill trim where the aluminum tape will attach. ALUMINUM TAPE (Cut into 4 pieces.) ALUMINUM...
- Page 9 30. Line up the edge of the insulator with the rib on the 34. Using isopropyl alcohol on a shop towel, thoroughly left rear illuminated door sill trim. clean the door sill trim harness fuse case where the fuse label will attach. INSULATOR DOOR SILL TRIM LEFT REAR...
- Page 10 With Other Accessory Harness 12-pin Connector 38. Secure the door sill trim harness to the vehicle harness with two wire ties. 37. If the 12-pin connector is already used by other accessory, locate the 12-pin connector taped to the DOOR other accessory harness.
- Page 11 40. Route the door sill trim harness as shown. 42. Route the door sill trim harness as shown. FRONT DOOR SILL TRIM HARNESS FRONT ASPIRATOR HOSE DOOR SILL GLOVE BOX TRIM 41. Line up the green tape on the door sill trim harness OPENING HARNESS with the vehicle clip, and secure the door sill trim...
- Page 12 44. Line up the green tape on the door sill trim harness 46. Plug the two door sill trim harness 2-pin connectors with the vehicle clip, and secure the door sill trim into the right front illuminated door sill trim harness to the vehicle harness with one wire tie.
- Page 13 47. Secure the right front illuminated door sill trim 48. Position the right front illuminated door sill trim to the harness, subharness, and 2-pin connectors to the vehicle panel as shown. vehicle harness with two wire ties. RIGHT FRONT ILLUMINATED DOOR SILL TRIM HARNESS 4 CLIPS VEHICLE...
- Page 14 51. Secure the subharness to the vehicle harness with 53. Secure the subharness and 2-pin connectors to the three wire ties. vehicle harness with two wire ties. WIRE TIE SECTION VIEW SUBHARNESS SUBHARNESS VEHICLE HARNESS VEHICLE HARNESS 2-PIN CONNECTORS VEHICLE PANEL 2 WIRE TIES 54.
- Page 15 56. Remove the right rear illuminated door sill trim. 58. Install the passenger’s kick panel, and install the right front illuminated door sill trim. RIGHT REAR ILLUMINATED DOOR SILL TRIM PASSENGER’S KICK PANEL RIGHT FRONT ILLUMINATED DOOR SILL TRIM 4 CLIPS 57.
- Page 16 60. Position the left front illuminated door sill trim to the 63. Remove the left front illuminated door sill trim. vehicle panel as shown. LEFT FRONT ILLUMINATED DOOR SILL TRIM HARNESS (Do not slack.) LEFT FRONT ILLUMINATED 4 CLIPS VEHICLE VEHICLE DOOR SILL TRIM (Do not secure.)
- Page 17 65. Plug the door sill trim harness 2-pin connector into 67. Position the left rear illuminated door sill trim to the the left rear illuminated door sill trim 2-pin connector. vehicle panel as shown. VEHICLE DOOR SILL PANEL TRIM HARNESS 4 CLIPS 2-PIN (Do not secure.)
- Page 18 70. Install the left center pillar lower trim, and install the 72. Check that all wire harnesses are routed properly left rear illuminated door sill trim. and all connectors are plugged in. 73. Install all removed parts. LEFT CENTER 74. Connect the negative cable to the battery. PILLAR LOWER TRIM 75.