KitchenAid KEBS107SSS04 Tech Sheet

Tech Sheet
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
IMPORTANT
Electrostatic Discharge (ESD) Sensitive Electronics
:
ESD problems are present everywhere. ESD may damage or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress.
Use an antistatic wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the appliance
Touch your finger repeatedly to a green ground connection point or unpainted metal in the appliance.
Before removing the part from its package, touch the antistatic bag to a green ground connection point or unpainted metal
in the appliance.
Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.
When repackaging failed electronic control assembly in antistatic bag, observe above instructions.
Fahrenheit (°F) to Celsius (°C) Conversion
The temperature is preset in Fahrenheit; however, it can be changed to
Celsius.
To Change: Press OPTIONS and then "1" to toggle temperature between
Fahrenheit and Celsius settings.
When in Fahrenheit, "°F" follows the oven temperature.
When in Celsius, "°C" follows the oven temperature.
Adjust Oven Temperature Calibration:
1. Press OPTIONS and then "6" to set the calibration.
2. On double ovens only, press UPPER OVEN or LOWER OVEN to select
oven.
Each oven calibration can be independently set.
3. Press "3" to increase and "6" to decrease the temperature.
4. Press START to end calibration.
W10220952A
Software copyrighted. This product is covered by one or more of the
4,852,544 5,424,512
4,974,804 5,438,180
5,008,516 5,441,036
5,064,998 5,491,314
5,138,137 5,571,433
5,142,125 5,571,434
5,175,413 5,620,623
5,185,047 5,694,916
5,321,229 5,749,388
5,349,162 5,756,970
5,378,874 5,767,488
5,382,552 5,808,278
5,422,460 5,810,576
-OR-
Is the oven in "Sabbath Mode"? If so, "SAB" will appear in the digital
display. Press OPTIONS and "7" to end Sabbath mode. This will
return the oven to BAKE mode for an untimed bake.
Unplug oven or disconnect power before performing the following checks:
A potential cause of a control not functioning is corrosion on
connections. Observe connections and check for continuity with an
ohmmeter.
All tests/checks should be made with a VOM or DVM having a
sensitivity of 20,000Ω per volt DC or greater.
Check all connections before replacing components, looking for
broken or loose wires, failed terminals, or wires not pressed into
connectors far enough. Damaged harness must be entirely replaced.
Do not rework a harness.
Resistance checks must be made with power cord unplugged from
outlet, and with wiring harness or connectors disconnected.
Programming the Cavity Size
1. Unplug oven or disconnect power.
2. Wait 10 seconds, then plug in oven or reconnect power.
3. Enter Diagnostics mode by pressing OFF, OFF, START.
4. Press key #6 to show cavity size select screen.
5. To edit, press CLOCK key.
6. Scroll through cavity sizes by pressing key #6 until required size is
displayed.
7. Once correct size is displayed, press the START key to accept
modification.
following patents U.S. Patent Nos.
5,813,320 6,017,211
5,841,112 6,035,848
5,856,654 6,043,461
5,881,710 6,079,756
5,910,265 6,087,944
5,918,589 6,097,000
5,924,857 6,111,231
5,928,543 6,163,017
5,961,311 6,201,222
5,967,634 6,232,584
5,983,888 6,263,782
6,008,478 6,349,717
Other Patents Pending.
Diagnostics
FOR SERVICE TECHNICIAN'S USE ONLY
Do not discard
6,363,971 6,693,262
6,375,150 6,698,417
6,392,204 6,698,923
6,394,081 6,700,101
6,403,929 6,722,356
6,437,294 6,734,403
6,509,551 6,784,404
6,545,251 6,841,761
6,570,136 6,870,138
6,614,006 6,904,969
6,663,009 6,930,287
6,666,676 6,935,330