Service Points; Tyre Pressure - Stiga TITAN 26 B Instructions For Use Manual

6.2 SERVICE POINTS

1st time Interval
Service point
Hours of operation/
Calendar months
Water separator,
check
Pre-filter, cleaning
Fuel filter, replace

Tyre pressure,

check, adjust
Engine oil, filter,
change
Hydraulic oil, fil-
ter, tank vent valve,
change/clean
Wheel motors ,
change oil
Belt transmissions,
check
Cooling system,
clean
Battery, check
Air filter, clean pre-
filter
Air filter, change
inner filter
Lubrication
Adjusting valves
Grinding valves
6.3 PREPARATION
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by
always applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by removing the ignition key.
6.4 WATER SEPARATOR
There is a float in the water separator (17:E) that
can be viewed through the transparent cup. The
float must be at the bottom. If the float has risen,
the water separator must be cleaned as follows:
1. Shut off the water separator tap. See fig. 17.
2. Hold a container under the water separator to
collect fuel.
3. Open the cup by pressing its ring (17:A).
ENGLISH
.
See
para-
graph
50/- 6.4
6.4
400/- 6.5
6.7
50/12 200/12 6.8
50/12 400/12 6.9
50/12 200/12 6.10
50 200/- 6.11
1000/12 6.12
50/- 6.13
6.14
6.14
6.15
1000/- 6.16
2000/- 6.16
4. Carefully remove the cup (17:B) and remove
the spring (17:D) and float (17:E) from the cup.
5. Clean the inside of the cup and thread filter
(17:C).
6. Check that the O-ring is intact and reinstall the
components in reverse order.
7. Open the tap.
8. Bleed the fuel system. See "5.12".
Clean the fuel tank if water accumulates in the wa-
ter separator often. Contact an authorised work-
shop.
6.5 FUEL FILTER (26B, 26H)
1. Shut off the fuel filter's tap. See fig. 18.
2. Hold a container under the fuel filter to collect
fuel.
3. Detach the cup by turning its ring (18:J).
4. Carefully remove the cup (18:H) and remove
the filter (18:F).
5. Clean the inside of the cup (18:H).
6. Check that the O-ring (18:G) is intact and rein-
stall the components with new filter in reverse
order.
7. Open the tap.
8. Bleed the fuel system. See "5.12".
6.6 FUEL FILTER (32H)
1. Stop the engine and allow it to cool.
2. Close all the fuel taps.
3. Use an oil filter wrench to slacken off the filter
(19, 20:P) in the direction (19:Dis). Carefully
remove the filter to prevent the spillage of fuel.
Wipe up any spilled fuel.
4. Clean around the mounting surface of the filter.
5. Apply a thin layer of fuel to the new filter gas-
ket.
6. Install the new filter by rotating it in the direc-
tion (19:Ass) until the gasket comes into con-
tact with the mounting surface.
7. Then tighten the filter a further turn using the
filter wrench.
6.7 TYRE PRESSURE
Set the tyre pressures to their default pressures.
Pressure front and rear: 0.9 bar.
See pressures in the manual for relevant imple-
ment.
6.8 CHANGING ENGINE OIL, FILTER
The engine oil may be very hot if it is
drained off directly after the engine is
shut off. So allow the engine to cool a
few minutes before draining the oil.
Change engine oil and filter as follows:
1. Place the machine on a level surface and run the
engine to operating temperature.
EN
91