7. Test run
7.2.3.
Using
SW4
in outdoor
unit
Refer
to the outdoor
unit installation
manual.
_--
:::A}
:k F}
Fig. 7-3
N
Fig. 7-4
7.3. Self-check
7,3.1,
Wired
remote
controller
(Fig.
7-3)
i Turn on the power.
_i Press the [CHECK]
button
mice.
_iSet
refrigerant
address
with [TEMPI
button
if system
control
is used.
_i Press the [ON/OFF]
button
to stop the self-check.
CHECK button
B Refrigerant address
TEMP. button
b IC:
Indoor unit
OC:
Outdoor unit
E Check code
F Unit address
7.3.2.
Wireless
remote
controller
(Fig.
7-4)
i Turn on the power.
CHECK
(2 Press the _
button
twice.
(Start
this operation
from the status
of remote
controller
display
turned
off.)
begins to light.
a "00" begins to blink.
(_ While
pointing
the remote
controller
toward
the unit's
receiver,
press the [_
button.
The
check
code will be indicated
by the number
of times
that the buzzer
sounds
from
the receiver
section
and the number
of blinks of the operation
lamp.
_i Press the ON/OFF
button
to stop
the self-check.
• Refer
to the following
tables
for details
on the check
codes.
(Wireless
remote
controller)
[Output
pattern
A[
Beeper
sounds
Beep
Beep
Beep
Beep
Beep
Beep
Beep
OPERATION
[lJ-[
_
r_
,J_
_
r_
_
...Repeated
INDICATOR
_
4
_-
b
lamp
flash
_
Off
On
On
On
On
Off
On
On
_attern
Self-check
Approx.
2.5 sec.
0.5 sec.
0.5 sec.
0.5 sec.
0.5 sec.
Approx.
2.5 sec.
0.5 sec.
0.5 sec.
starts
y
-._
(Star[
signal
received)
Number
of flashes/beeps
in pattern
indicates
the
check
Number
of flashes/beeps
in pattern
indicates
code
in the following
table
(i.e.,
n=5
for
"P5")
the
check
code
in the following
table
[Output
pattern
B[
Beeper sounds
Beep
Beep
Beep
Beep
Beep
O E A ,O.
I
LF:LFq_q __ra
I
INDICATOR
_
_
_ <
_
4
lamp flash
Off
On
On
On
On
On
Off
On
_attern
Self-check
Approx. 2.5 sec.
Approx. 3 sec.
0.5 sec. 0.5 sec. 0.5 sec.
0.5 sec. Approx. 2.5 sec.
Approx. 3 sec.
starts
_'
)
(Start signal
Y
received)
Number of flashes/beeps
in pattern indicates the check
code in the following table (i.e., n=5 for "U2")
Beep
Beep
• .. Repeated
On
On
0.5sec.
0.5 sec.
k
Y
Number of flashes/beeps in pattern indicates
the check code in the following table
[Output
pattern
A[
Errors
detected
by indoor
unit
Wired
remote
Wireless
remote
controller
controller
Beeper
sounds/OPERATION
INDICATOR
lamp flashes
Check
code
(Number
of times)
No
Check
code
Symptom
1
2
P9
3
E7
4
6
7
8
9
10
11
12
sound
P1
P2,
E6,
P4
P5
PA
P6
EE
P8
E4
Fb
Intake
sensor
error
Pipe (Liquid
or 2-phase
pipe) sensor
error
Indoor/outdoor
unit communication
error
Float switch
connector
CN4F open.
Drain
pump
error
Forced
compressor
error
Freezing/Overheating
safeguard
operation
Communication
error
between
indoor
and outdoor
units
Pipe temperature
error
Remote
controller
signal
receiving
error
Indoor
unit control
system
error
(memory
error, etc.)
No corresponding
Remark
12