6.
Electrical
work
4)Assigning
a remote
controller
to
each
unit
(Fig.
6=7)
Each
unit can be operated
only by the assigned
remote
controller.
Make
sure each
pair of an indoor
unit PC board
and a remote
controller
is
assigned
to the same
pair No.
5) Wireless
remote
controller
pair
number
setting
operation
::i )Press
the SET
button
with something
sharp
at the end.
Start this operation
from
the status
of remote
controller
display
turned
off.
D
blinks
an d Model
No. is lighted.
m_n
::2 Press the [_
button
twice
continuously.
Pair No. "0" blinks,
::3 Press the temp _(_
button
to set the pair number
you want
to set.
::_)Press
the SET
button
with something
sharp
at the end.
Set pair number
is lighted
for three seconds
then
turned
off.
::_ Pair No. of wireless
remote
controller
Indoor
PC board
0
Factory
setting
1
Cut J41
2
Cut J42
3-9
Cut J41, J42
Fig. 6-7
Mode
number
Setting
number
_
Refdgerant
address
_/_ Unit number
LtLI L_L_
e
PL NCTI_ , N
[ 0' '2
mm
CsC_C_Ct
®
$
CcC¢LIL_
Fig. 6-8
6.3. Function
settings
6.3.1
Function
setting
on
the
unit
(Selecting
the
unit
functions)
1) For
wired
remote
controller
(Fig.
6=8)
Changing
the power
voltage
setting
• Be sure
to change
the power
voltage
setting
depending
on the voltage
used.
iGo
to the function
setting
mode.
Switch
OFF the remote
controller.
Press
the ;A_ and
buttons
simultaneously
and hold them for at least
2
seconds.
FUNCTION
will start
to flash.
_; Use the _; button
to set the refrigerant
address
(m)
to 00.
_; Press
and [--] will start
to flash
in the unit number
(IV) display.
_;Use
the _; button
to set the unit number
(IV) to 00.
_[ Press the ;E; MODE
button
to designate
the refrigerant
address/unit
number.
[--]
will flash
in the mode
number
( I ) display
momentarily.
_; Press the F; buttons
to set the mode
number
( ][ ) to 04.
_; Press the
G; button
and the current
set setting
number
( _ ) will flash.
Use the
button
to switch
the setting
number
in response
to the power
supply
voltage
to be used.
Power
supply
voltage
230V
:
setting
number
= 1
208 V
:
setting
number
= 2
_; Press the MODE
button
;E; and mode
and the setting
number
( I ) and ( _ ) will
change
to being
on constantly
and the contents
of the setting
can be confirmed.
_ Press the FILTER
;A; and TEST
RUN B; buttons
simultaneously
for at least
two
seconds.
The function
selection
screen
will disappear
momentarily
and the air
conditioner
OFF display
will appear.
__L.,
io
J/--/I
Fig. 6-9
2) For
wireless
remote
controller
(Fig.
6-9)
Changing
the power
voltage
setting
• Be sure
to change
the power
voltage
setting
depending
on the voltage
used.
::i :Go to the function
select
mode
Press the _
button
twice
continuously.
(Start this operation
from the status
of remote
controller
display
turned
off.)
is lighted
and "00" blinks.
Press the temp _'_ button :€;) once to set "50". Direct
the wireless
remote
controller
toward
the receiverV> of the indoor
unit and press
the [_
button
:_L
::2 Setting
the unit number
Press the temp _)) _A_ button
::_. and :u to set the unit number
"00". Direct
the
wireless
remote
controller
toward
the receiver
of the indoor
unit and press
the
button
::_ Selecting
a mode
Enter 04 to change
the power
voltage
setting
using
the (_
::_:: and _
:_: buttons.
Direct
the wireless
remote
controller
toward
the receiver
of the indoor
unit and
h
press the _
button
Current
setting
number:
1 = 1 beep (one second)
2 = 2 beeps
(one second
each)
3 = 3 beeps
(one second
each)
::_ Selecting
the setting
number
Use the _
::_:: and _A_
buttons
to change
the power
voltage
setting
to 01
(230 V). Direct
the wireless
remote
controller
toward
the sensor
of the indoor
unit
q
h
and press the _
button
::STo select
multiple
functions
continuously
Repeat
steps
and
to change
multiple
function
settings
continuously.
::6 Compete
function
selection
Direct
the wireless
remote
controller
toward
the sensor
of the indoor
unit and press
the _
button
:_.
Note:
Whenever
changes
are made
to the function
settings
after
installation
or
maintenance,
be sure
to record
the changes
with
a mark
in the "Setting"
column
of the Function
table.
6.3.2
Function
setting
on the remote
controller
Refer to the indoor unit operation manual.
10