Sealey Quality machinery SM43.V3 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. ELECTRICAL SAFETY
 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current
device (rcd) is used. It is particularly important to use an rcd with portable products that are plugged into a supply which is not protected by
an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current device by contacting your sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. the Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2.
and use a Portable Appliance tester.
1.1.4. ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6. Important: ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that the restraint is tight.
double insulated products, which are always marked with this symbol
to rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10. If an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of
2.5mm² section cable.
1.2. GENERAL SAFETY
WARNING! ensure that Health & safety, local authority and general workshop practice regulations are adhered to when using this equipment.

familiarise yourself with the application, limitations and hazards of the saw.

WARNING! disconnect the saw from the mains power and ensure that the cutting

blade is at a complete standstill before attempting to change blades or perform
any maintenance.
Maintain the saw in good condition (use an authorised service agent).

replace or repair damaged parts. use genuine parts only. unauthorised parts may

be dangerous and will invalidate the warranty.
WARNING! Keep all guards and holding screws in place, tight and in good working

order. check regularly for damaged parts. A guard or any other part that is damaged
should be repaired or replaced before the machine is used. the safety guard is a
mandatory fitting where the saw is used on premises covered by the Health & safety
at Work Act.
locate saw in a suitable work area and keep area clean and tidy and free from

unrelated materials. ensure that there is adequate lighting.
Keep the saw clean and blades sharp for best and safest performance.

ensure that there are no flammable or combustible materials in or near the work area.

WARNING! Always wear approved eye or face protection when operating the saw. use a face or dust mask if dust is generated.

Maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.

remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.

, are fitted with live (brown) and neutral (blue) wires only.
Original Language Version
InstructIons for:
SCROLL SAW
SM43.V3
Model no:
Yellow & Green
Earth Wire
Blue
Neutral
Wire
FUSE RATING
3 AMP
fig. 1
Brown
Live
Wire
Cable
Restraint
sM43.V3 Issue: 5 - 07/01/10