Table of Contents
Advertisement
JBL VLA-C SERIES | USER'S GUIDE
12 - SPECIFICATIONS
VLA-C265
Two-Way Full Range Dual 10" Array Module
System:
Frequency Range (-10 dB)
Frequency Response (±3 dB)
System Power Rating
Maximum Input Voltage:
Maximum SPL (1m)
Sensitivity
Coverage Pattern (-6 dB):
Impedance:
Amplifiers:
Transducers:
Low Frequency Driver:
High Frequency Driver:
Physical:
Enclosure Material:
Grille:
Inter-Enclosure Angles:
Environmental:
Terminals:
Colors:
Dimensions (H x W x D):
Net Weight (ea):
Shipping Weight (ea):
Included Accessories:
Optional Accessories:
1. Using recommended DSP tuning, full-space (4π)
2. Continuous Pink Noise rating is IEC-shaped pink noise with 6 dB crest factor. Peak defined as 6 dB above Continuous Pink Noise Rating.
3. Continuous Average calculated from sensitivity and power handling, exclusive of power compression. Peak measured, unweighted SPL, bi-amp mode,
measured under full-space conditions at 1 meter using broadband pink noise with a 12 dB crest factor and specified preset.
4. 2.83 V RMS, full-space (4π)
JBL continually engages in research related to product improvement. Some materials, production methods and design refinements are introduced into
existing products without notice as a routine expression of that philosophy. For this reason, any current JBL product may differ in some respect from its
published description, but will always equal or exceed the original design specifications unless otherwise stated.
:
85 Hz - 19 kHz
1
1
:
108 Hz – 16.5 kHz
2
:
Full Range:
800 W Continuous Pink Noise (3200 W peak), 2 hrs
400 W Continuous Pink Noise (1600W peak), 100 hrs
Bi-amp LF:
800 W Continuous Pink Noise (3200 W peak), 2 hrs
400 W Continuous Pink Noise (1600W peak), 100 hrs
Bi-amp HF:
150 W Continuous Pink Noise (600 W peak), 2 hrs
50 W Continuous Pink Noise (200 W peak), 100 hrs
Full-Range:
80 V Rms (2 hrs), 160 V peak
Bi-Amp LF:
80 V Rms (2 hrs), 160 V peak
Bi-Amp HF:
50 V Rms (2 hrs), 135 V peak
:
131 dB Cont. Ave (2 hrs), 137 dB Peak
3
:
Full-Range:
102 dB (85 Hz – 19 kHz)
4
Bi-Amp LF:
100 dB (85 Hz – 950 Hz)
Bi-Amp HF:
108 dB (950 Hz – 19.2 kHz)
Horizontal:
65° (+15°/-10°, 1.5 kHz to 15 kHz)
Vertical:
Varies with array size and configuration
Full-Range:
8Ω, 6.6Ω min @ 162 Hz
Bi-Amp LF:
8Ω, 6.8 Ω min @ 162 Hz
Bi-Amp HF:
16 Ω, 16.2 Ω min @ 11 kHz
Crown DCi Family with DSP on-board
Recommended
Crown DCi 2 | 1250N
Crown DCi 4 | 1250N/ND/DA
Crown DCi 2 | 2400N
Crown DCi 4 | 2400N
2 x 2261FF, 254 mm (10 in) diameter, each with two 76 mm (3 in) diameter voice coils, Neodymium Differential
Drive
®
, Direct Cooled
™
3 x 2415K, D2 Dual Diaphragm Dual Voice Coil Compression Drivers, each with two 38 mm (1.5 in) dia. Voice Coils; 21
mm (0.8 in) exit
Fiberglass shell, gelcoat finish, with 18 mm Birch plywood internal bracing.
Powder coated 14 gauge hex-perforated steel with zinc under-coating, backed with acoustically transparent cloth
and hydrophobic screen.
VLA-C265 to VLA-C265: 1.5°, 2.4° 3.8°, 6.0°, 9.5° using VLA-C265 Bracket Plate (included with VLA-C265)
VLA-C265 to VLA-C2100 (either model on top/bottom): 1.9°, 3.0° using VLA-C2100 Bracket Plate (included with
VLA-C2100) and 4.7°, 7.5°, 11.9° using VLA-C265 Bracket Plate (included with VLA-C265)
VLA-C265 below VLA-C125S Subwoofer (VLA-C265 cannot be connected above C125S): 0°, 5° using VLA-C125S
Bracket Plate (included with VLA-C125S)
IP-55 rating per IEC529 (dust protected and protected against jets of water).
CE-compliant covered barrier strip terminals. Barrier terminals accept up to 5.2 sq mm (10 AWG) wire or max width
9mm (0.375 in) spade lugs. Touch-proof covers.
-GR: Gray (similar to Pantone 428C), -BK: Black
381 x 848 x 460 mm (15.0 x 33.4 x 18. 1 in)
37.7 kg (83 lbs)
44.0 kg (97 lbs)
2 pcs. VLA-C265 Bracket Plates
8 pcs. M10 x 35 mm stainless steel bolts (1.5mm pitch, 6 mm hex-drive) for attaching Bracket Plates
2 pcs. Plastic Trim Cover Panels for Bracket Plates, each attaches via
4 pcs (8 total) 3-32 x ½" trusshead, phillips-drive, stainless steel bolts.
VLA-C-SB Suspension Bar Kit for the array, includes 2 identical Suspension Bars (for top/bottom), 4 pcs ¾-inch Class
2 Screw Pin Shackles (must use 2 Shackles for each Suspension Bar, located at end channels, not in the center).
27
Advertisement
Table of Contents
