Table of Contents
Advertisement
Radio Reception
-
+
STANDBY-ON
SOURCE
BAND
PROG/CLOCK
VOLUME
TUNING
Tuning to radio stations
1
Select TUNER source.
is displayed.
TUNER
2
Press BAND (TUNER on the remote
control) once or more to select your waveband.
3
Turn TUNING 0 to tune to a station.
Display shows: the frequency of the tuned
station.
Maintenance
Cleaning the Cabinet
Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution
containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
When a disc becomes dirty,
clean it with a cleaning cloth.
Wipe the disc from the centre
out.
Do not use solvents such as
benzene, thinner, commercially
available cleaners, or antistatic
spray intended for analogue records.
Other Connection
Helpful hints:
To improve radio reception:
– For FM, extend coil antenna at the back of the
unit fully for optimum reception.
Listening to an external source
You can listen to the sound of the connected
external device through your system's speakers.
1
Select AUX source.
2
Use a line-in cable (not supplied) to connect
MCM 108's AUX-IN jack (3.5 mm ) to an
AUDIO OUT or headphone jack on an
external equipment (such as CD player, or VCR).
Cleaning the disc lens
After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
playback quality, clean the disc lens with Philips
CD Lens Cleaner or any commercially available
cleaner. Follow the instructions supplied with
cleaner.
Clock/Timer
M I C R O S Y S T E M
M C
M
1 0 8
iR
Setting the clock
1
In Standby mode, press PROG/CLOCK
button.
The clock digits for the hours flash.
2
Press ¡1 / 2™ to set the hours.
3
Press PROG/CLOCK again.
The clock digits for the minutes flash.
4
Press ¡1 / 2™ to set the minutes.
5
Press PROG/CLOCK to confirm the time.
Note:
– If the clock has not been set, -- --:-- -- will be
displayed.
Setting the timer
The system can be used as an alarm clock. CD
or TUNER can be set to switch on at a preset
time. The clock time needs to be set first
before the timer can be used.
If no button is pressed within 90 seconds during
timer setup, the system will exit timer setting
mode automatically.
1
In any mode, press TIMER on the remote
control for more than 2 seconds.
2
Press ¡1 / 2™ (or CD / TUNER on the
remote control) to select sound source.
3
Press TIMER to confirm your desired source.
The clock digits for the hours flash.
9
4
Press ¡1 / 2™ to set the hours.
5
Press TIMER again.
The clock digits for the minutes flash.
6
Press ¡1 / 2™ to set the minutes.
7
Press TIMER to confirm the time.
The timer is now set and actiated.
Notes:
- If source CD is selected and no disc is in the CD
tray or the disc has an error, TUNER will be
selected automatically.
- At the set time of wake up, the set will turn on at
volume level 12.
AUX-IN
To activate and deactivate timer
In standby or during playback, press
TIMER once.
Display shows
if activated, and
disappears if deactivated.
Activating and deactivating
SLEEP
The sleep timer enables the system to switch
off by itself after a set period of time. The clock
time needs to be set first before the sleep timer
can be used.
Press SLEEP on the remote control repeatly
to select desired time before
system shuts off.
Display shows
and
SLEEP
series of time options for
selection:
,
,
,
,
To deactivate, press SLEEP on the remote
control once or more until "
press STANDBY ON y on the system or
remote control.
SLEEP
TIMER
,
...
" is shown, or
10
Advertisement
Table of Contents
