Car Installation; Installation With Base - Chicco Oasys 0+ UP BebeCare Instructions Manual

P. Release handle (from the base and stroller)
Fig. 4A (Tray open)
Q. Headrest and belt adjustment button
R. Compartment for storing the instruction
manual
1.4 POSITIONS OF THE HANDLE
The child car seat carry handle can be ad-
justed in 6 different positions (Fig. 5).
A. Position in car without base.
A1. Position in car with base (WARNING:
positions A and A1 are the only positions
allowed during use in the car).
X. NEVER use.
B. Position when carried by hand.
C. Rocker chair mode position or when you need
to fasten it to an appropriate Chicco stroller.
D. Fixed rocker chair position.
To adjust the position, press both buttons
(M) on the handle bar together and rotate
it to the desired position until you hear it
click into place.
1.5 RESTRICTIONS
MENTS REGARDING THE USE OF
THE PRODUCT AND CAR SEAT
WARNING! Strictly complies with the follow-
ing restrictions and requirements for use
concerning the product and vehicle's seat:
safety will not be guaranteed otherwise.
• The child car seat can be fitted on the front
passenger seat or any other back seat. In any
case the vehicle seat must be used forward
facing. Never use this Car seat rear facing on
any vehicle's seat (Fig. 6). The vehicle's seat
must be equipped with 3-point seat belts
whether static or retractable, approved
according to UN/ECE Regulation No. 16 or
other equivalent standards (Fig. 7).
• WARNING! In case of use in vehicles equip-
ped with rear seat belts with integrated
airbags (inflatable belts), the interaction
of the inflatable portion of the vehicle's
belt with this child restraint can result in
serious injury or death! Do not install this
child restraint using an inflatable seat belt.
• WARNING! Never fit the child car seat to a
vehicle seat that is only equipped with a
2-point safety belt (Fig. 8)
• Never use the booster cushion if the child
weighs more than 6 kg.
AND REQUIRE-
• Make sure that the car's 3-point seat belt
buckle is not too high (Fig. 11- 15). Other-
wise, try to install the car seat on another
vehicle's seat.

2. CAR INSTALLATION

The child car seat can be installed with or
without base (E). In either case, the child car
seat must always be installed rear facing.

2.1 INSTALLATION WITH BASE

To install the child car seat with base on the
vehicle seat, proceed as follows:
1. Remove the child car seat from the base
(E) by pulling the release lever behind the
backrest and then lift it up using the carry
handle (Fig. 9).
2. Position the base on the chosen vehicle's
seat. Position it as seen in Fig. 10 in order
to touch the vehicle seat's backrest.
3. Pull the vehicle safety belt and fasten
it to the relevant buckle, inserting the
horizontal (waist) part of the belt through
the two blue slots (L) and pull it as tightly
as possible (Fig. 11).
4. Attach the child car seat on the base (rear
facing) and push it down until you hear it
click into place (Fig. 12).
5. Check that the child car seat is correctly
fitted on the base by lifting the front and
rear sections.
6. Pull the diagonal car safety belt and thread
it through the relevant slot (O) on the
back of the child car seat's backrest (Fig.
13) WARNING! When travelling by car, this
diagonal safety belt must ALWAYS be
threaded through this slot.
7. Pull the belt as tightly as possible, without
leaving any slack and making sure it is
not twisted.
8. Turn the carry handle to position A1 (Fig.. 14).
WARNING! After installing the child car seat,
ALWAYS check that the vehicle safety belt is
tightened properly along the entire length
of the belt and that no parts are twisted.
NEVER fit the car safety belt in any other
way not mentioned in these instructions.
To remove the child car seat leaving the
base on the vehicle seat:
1. Unthread the diagonal belt through the
slots in the backrest without removing it
from the buckle.
2. Bring the handle bar to vertical position
23