SECO-LARM E-931-S33PRQ Manual

ENFORCER 33ft Polarized Reflective Photoelectric Beam Sensor Reflective Photoelectric Beam Sensor
Sample Applications:
Garage
Gate
Door
Optional Accessory:
Reflector Hood
E-931ACC-HR
Provides extra
protection for the
reflector.
Compatible with Reflective Photoelectric Beam Sensor models
E-931-S50RRQ, E-931-S35RRQ, and E-931-S33PRQ.

Troubleshooting:

Sensor does not detect the object.
The beam sensor LED will not turn green.
Beam sensor LED lights when object
is detected, but there is no output.
WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM's obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, r
or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM d
equipment is not operating properly as a result of causes other than defects in material and workmanship. equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser's exclusive remedy, shall be limited to replacement or repair only, at LARM, and the purchaser's exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM's option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal LARM be liable for any special, collateral, incidental, or consequential personal
or property damages of any kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
®
U.S.A., Inc.
SECO SECO- - - - LARM SECO SECO LARM LARM LARM
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
4
Vehicle Assembly
Detection Line
Other Sensors Available: Other Sensors Available:
Reflective Dual and Dual and Curtain and
Photobeam Quad Beam Quad Beam Barrier
• Change the angle of the sensor or readjust Change the angle of the sensor or readjust
the sensitivity setting. the sensitivity setting.
• Clean the sensor and reflector with a damp Clean the sensor and reflector with a damp
(not wet) cloth.
• Adjust the reflector and/or sensor for proper Adjust the reflector and/or sensor for proper
alignment.
• Check wiring between the sensor and local Check wiring between the sensor and local
alarm device.
rkmanship while used in normal service
LARM's obligation is limited to the
-LARM.
LARM determines that such
re current at the time of publication. However, the
LARM reserves the right to
or typographical errors.
Website: www.seco-larm.com
E-mail: info@seco-larm.com
MiE-931-S33PRQ_1301.docx
SECO-LARM U.S.A., Inc. LARM U.S.A., Inc.
33ft Polarized Reflective Photoelectric Beam
Polarized sensor is immune to
•
• shiny objects: Triggers only when
correctly reflected light is detected.
•
Weatherproof (IP66)
•
• Anti-condensation housing
Input voltage 12~250 VAC/VDC
•
Caution:
• This sensor is not designed to prevent bodily injury or loss of life.
• This sensor is not designed for use in environments where explosive gasses may be present.
• Use of this sensor in certain security applications may be regulated by local laws or codes. SECO-LARM is not
responsible for compliance with such laws or codes.
PITSW3
Note: Products with model numbers that end with "Q" or that have a round green "Q" sticker are RoHS compliant.
E-931-S33PRQ
Sensor
Manual
Up to 33ft (10m) sensing range
•
• Round reflector, Dia.: 82 mm.
Form C relay: 1A@30VDC
•
Beam status LED
•
• N.C. Tamper switch:
500mA@30VDC