Sleep; Time; Memo 3/Memo 4; Tuning 3/4 - Grundig Yacht Boy 360 Manual

FRONT OF UNIT
DISPLAY – Multifunction display
POWER – Switches the unit on and off
You can switch the unit off even if all buttons are locked (in
LOCK position)

SLEEP

– For entering a time after which the unit is switched off (sleep
time). Initial value: 60 minutes. This value is decreased in
steps of 10 minutes by repeatedly pressing this button.
– Short pressure on the SLEEP button: Indication of the remai-
ning sleep time for approx. 5 seconds in the display (left).
AUTO – for switching between three function modes:
– Wake-up with radio. The display indicates .
– Wake-up with sound signal (also with switched-on radio).
The display indicates .
– Wake-up function off. When switching to this function, the
display indicates for approx. 5 seconds '-:--'.
ON TIME – Switch on time
– For calling up the wake-up time (in the left numeric block)
when the radio is switched on.
– For setting the wake-up time (switch-on time).
TIME 1/2 – Time I/II
– For selecting between Time I and Time II.
– For setting and calling up the times I and II.
FREE – Indicates free memory positions in increasing order.
– Two successive pressures on this button will clear occupied
memory positions (e.g. 4 FREE FREE).
STORE – Store in memory up to 40 stations
To avoid redundant storing, first check whether the currently
received station has already been stored.
If the station has not yet been stored, enter the number of
the desired memory position and store the station in
memory by pressing the STORE button (e.g. 13 STORE).
If the selected memory position is not free, the indication
will flash for approx. 5 seconds. The memory position will
not be overwritten.
– Two pressures on the button will overwrite occupied
memory positions (e.g. 23 STORE STORE): The selected
memory position is overwritten and occupied by the station
currently tuned to.
FM – For selecting the desired FM (VHF) band.
– For clearing incorrect numeric entries
AM – For switching to the AM wavebands.
Repeated pressures on this button will select the wavebands
in the following order: LW - MW - SW - LW - MW - etc.
– For clearing incorrect numbers
RESET
– For clearing all stored data (memory positions, clock time).
– For resetting an eventually blocked keyboard (e.g. after
static charges.
LOCK – For locking all keys except the POWER button (for
switching off) and the SNOOZE button.
Your Yacht Boy 360 at a Glance
FRONT SIDE OF THE UNIT
0-9, • Numeric buttons and decimal point
– For direct numeric entries.
– Two pressures on this button will clear incorrect numeric entries.
FREQU./METER
– For entering frequencies
(e.g. 107.7 FREQU./METER = FM 107.7 MHz)
– For entering meter bands
(e.g. 13 FREQU./METER = 13 m).
MEMO 3 / MEMO 4
– For calling up the memory position 1...40.
(e.g. 20 MEMO 3/4 = call-up of memory position 20).
Press once: Next higher (3) or lower (4) memory position.
Press and keep longer than 1 s: Automatic memory position
selection in ascending or descending order.
The automatic memory position select function stops for
approx. 5 seconds on each memory position so that the
station received on it can be checked. A further pressure on
the MEMO 3/4 button will terminate this function.

TUNING 3/4

– For manual step-by-step tuning in direction of higher or
lower frequencies.
Keep button pressed: Frequency scan up or down.
STEP – For selecting the manual tuning steps
LW 1 kHz or 9 kHz
SW 1 kHz or 5 kHz
MW 1 kHz or 9 kHz resp. 10 kHz
SCAN – Automatic station tuning
– Press briefly: Automatic station tuning in direction of higher
frequencies.
– Press longer than 0.5 s: Automatic station tuning in
direction of lower frequencies.
TOP OF UNIT
Telescopic aerial – for FM and SW reception.
SNOOZE – Press once to switch off the radio or the alarm
function after wake-up. After five minutes, the wake-up
function will be repeated (sound signal or radio).
– Keep the button pressed for longer than 2 seconds to switch
off the wake-up function. The function will be retained for
the following day(s).
– If the snooze button is not pressed, the sound signal will
sound for 5 minutes or the radio plays for 60 minutes. After
that, the respective function will be switched off.
LIGHT – Display illumination
– Press this button to illuminate the display. After 10
seconds, the illumination will automatically be switched off.
– The illumination time will be increased if any other button is
pressed within this 10-seconds period.
– A second pressure on the LIGHT button will immediately
switch off the display illumination.
YB360 page 13
GB
13