Shure Incorporated Table of Contents Modifikasi Internal SCM262Mixer Stereo Internal Modifications Disassembly PETUNJUK PENTING KESELAMATAN Supplied Hardware General Description Rackmount Installation Features Stand-Alone Installation Front Panel Fixed Installation Rear Panel Spesifikasi DIP Switches Voltage Gain (typical, controls full clockwise) Applications...
Shure Incorporated SCM262 Mixer Stereo PETUNJUK PENTING KESELAMATAN BACA petunjuk ini. SIMPAN petunjuk ini. PATUHI semua peringatan. IKUTI semua petunjuk. JANGAN gunakan perangkat ini dekat dengan air. CUKUP DIBERSIHKAN dengan kain lap kering. JANGAN halangi semua bukaan ventilasi. Berikan jarak yang cukup dengan lubang udara yang cukup dan pasang sesuai petunjuk pabrik.
Serahkan semua servis ke petugas ahli. Sertifikasi keamanan tidak berlaku jika voltase kerja yang ditetapkan pabrik diubah. General Description The Shure Model SCM262 is a stereo mixer intended for sound reinforcement applications that integrate microphones with consumer stereo products. It incorporates two active-balanced microphone inputs with three unbalanced stereo aux level inputs.
Shure Incorporated Front Panel ① MIC Channel Gain Controls, 1-2. Control the gain levels of the MIC channels and LINE IN 2 (MIC 2). ② STEREO Channel Gain Controls, 1-3. Control the gain levels from CD players, juke boxes, VCRs, or other consumer stereo equipment connected to the STEREO inputs.
Shure Incorporated Rear Panel ① Power Connector. Accepts 100-120 Vac (SCM262) or 220-240 Vac (SCM262E). ② Left/Right MIC/LINE Output Connectors. These 1/4-in. connectors are stereo, balanced outputs for use with professional audio equipment. Controlled by DIP switch. ③ Left/Right AUX Output Connectors.
Page 7
Shure Incorporated DIP Switches DIP SWITCH FUNCTION POSITION UP (default) POSITION DOWN LEFT OUTPUT MIC/LINE Line RIGHT OUTPUT MIC/LINE Line MIC 1 DUCKING MIC 2 DUCKING DUCKING LEVEL –∞ -20 dB STEREO 3 JUKEBOX MUTE 12 V PHANTOM LEFT/RIGHT OUTPUT MIC/LINE: DIP switches 1 and 2 adjust the left and right outputs for line- or mic-level operation.
Shure Incorporated STEREO 3 JUKEBOX MUTE: This DIP switch turns the Juke Box Mute feature on or off. When on, any source connected to STEREO 3 will mute STEREO 1 and 2 inputs. PHANTOM POWER: When in the down position, this switch activates a 12 V phantom power source for condenser microphones.
Shure Incorporated This feature is designed especially for use with jukeboxes, but will work for any equipment connected to STEREO 3. Set DIP Switch 6 to the down position (Jukebox Mute on). If the ducking application is used in conjuction with the Jukebox Mute application, then activated microphones will mute or duck the STEREO 3 input.
Shure Incorporated Disassembly To access the printed circuit board (pc board) for internal modifications, use the following steps: Unplug the power cord. Remove the knobs and retainer nuts from the front panel. Remove the two screws at each bottom corner of the front panel.
4 wood screws, 1/2 in. (1.25 cm). For fixed installations. Rackmount Installation The SCM262 can be mounted as a single unit or dual-mounted with either another SCM262 or another Shure half-rack unit such as the SCM268 or DFR11EQ. Attach the rackmount brackets using one of the following methods: Single unit (half-rack) installation: Attach the short and long rackmount brackets to the SCM262 with eight (8) of the supplied bracket screws.
Page 13
Shure Incorporated Dual-mounted installation: Connect the two units together side-by-side using two (2) straddle brackets. The brackets should straddle the recessed edges on the top and bottom of each chassis. Fasten them using eight (8) bracket screws. Be sure to use both straddle brackets-one on the top and one on the bottom.
Shure Incorporated Stand-Alone Installation Adhere the four (4) supplied rubber feet to the bottom of the unit at each corner. This will keep it from sliding and protect the table surface. Fixed Installation To permanently affix the SCM262 above or below a table, shelf, or counter top, use the following steps: Fasten the straddle brackets to the recessed edges of the chassis using four (4) bracket screws.
Shure Incorporated Spesifikasi Respon Frekuensi pada 1 kHz Sakelar Mic/Line 150 Hz dengan 20 kHz ±2dB Input Aux 20 Hz dengan 20 kHz ±2dB Low-Cut Filter -6 dB/oktaf di bawah 80 Hz 16/19...
Page 17
Shure Incorporated Total Distorsi Selaras 1 kHz, +4 dBu keluar, output mix (MASTER) di +0 dB <0,25% Kebisingan Input Setara sumber seimbang 150Ω, Bobot -128 dBV Noise Output kontrol kanal berlawanan arah jarum jam penuh, Bobot Master berlawanan arah jarum jam penuh...
Shure Incorporated Dimensi 43 x 218 x 162 mm (1,72 x 8,60 x 6,37 in.) Berat Netto 1,1 kg (2 lbs, 5 oz.) Voltage Gain (typical, controls full clockwise) Output Input Line Low-impedance mic (150 32 dB 72 dB 60 dB Ω)
Line (Power) Cord, 230-240 Vac (UK) 95A8713 Pemberitahuan Servis Untuk servis tambahan atau informasi komponen, hubungi departemen servis Shure di 1-800-516-2525. Di luar Amerika Serikat, hubungi Pusat Servis Shure resmi. Sertifikasi Produk ini memenuhi Persyaratan Utama terhadap semua petunjuk Eropa terkait dan memenuhi syarat untuk penandaan CE.