Sealey SA345.V2 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high
standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents,
WarninGs anD cautions. use tHis ProDuct correctLy anD WitH care for tHe PurPose for
WHicH it is intenDeD. faiLure to Do so May cause DaMaGe anD/or PersonaL inJury anD WiLL
inVaLiDate tHe Warranty. PLease KeeP instructions safe for future use.
1. safety instructions
 WarninG! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to
when using this equipment.
 WarninG! Disconnect from air supply before changing the blade, servicing or performing maintenance.
 Maintain the saw in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and
will invalidate the warranty.
 Use in suitable clean and tidy work area, free from unrelated materials. Ensure that there is adequate lighting.
 WarninG! Always wear approved eye or face and hand protection when operating the saw.
 Remove ill fitting clothing. Remove ties, loose jewellery and contain and/or tie back long hair.
 Wear appropriate protective clothing and keep hands and body clear of working parts.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the work area.
 Check moving parts alignment on a regular basis.
 Ensure workpiece is secure before operating the saw. Never hold a workpiece by hand. Use a vice or clamps.
 WarninG! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 50-90psi.
 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that
all connections are secure.
 Prolonged exposure to vibration from this saw poses a health risk. It is the employer's/owner's responsibility
to correctly assess the hazard and issue guidelines for safe periods of use and offer suitable protective
equipment.
 Do not use any power source except an air compressor.
 Do not operate saw near any inflammable substance or on any container that has held an inflammable
substance.
 Do not use the saw for a task it is not designed to perform.
 Do not operate saw if any parts are damaged or missing as this may cause failure and/or personal injury.
 Do not carry the saw by the hose, or yank the hose from the air supply.
 Do not operate saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 Do not carry the saw with your finger on the trigger.
 Do not direct air from the air hose at yourself or others.
 When not in use disconnect from air supply and store in a safe, dry, childproof location.
Reciprocating Air saw Model No. sA345 when operated in accordance with these instructions and tested in
accordance with Bs EN 28662-1:1993, Iso 8662-1:1988 and Bs EN Iso 28927-8:2009 results in the
following vibration emission declared in accordance with Bs EN 12096:1996.
Measured vibration emission value: 4.3m/s²
these values are suitable for comparison with emission levels of other tools that have been subject to the
same test.
this tool may cause hand-arm vibration syndrome if its use is inadequately managed.
recommended Measures to reduce risk of hand-arm vibration syndrome:
this tool should not be used by an individual regularly for more than
this duration of use should be reduced if the individual is exposed to hand-arm vibration from other sources.
risk of Hand arm Vibration injury
Original Language Version
INstRUCtIoNs foR:
low noise low vibration
reciprocating air saw
sa345.V2
MoDEl No:
uncertainty: 1.72m/s²
331 minutes in any 8 hour period.
sA345.V2 Issue: 2 - 19/06/12