Braun SI 6220 FreeStyle Manual page 3

All manuals and user guides at all-guides.com
Our products are engineered to meet the D After ironing
highest standards of quality, functionality and
•
design. We hope you enjoy your new Braun
FreeStyle.
Notice: Remove the sole plate label, if any,
•
before first use.
–––––––––––––––––––––––––––––––––––––––––
•
Important safeguards
• Before using the iron, read the use instruc-
tions completely. Keep the use instructions
during the entire life of the iron.
E Maintenance and cleaning
• Make sure your voltage corresponds to the
voltage printed on the iron. Connect the
iron to alternating current only.
• Always unplug the iron before filling with
water and make sure the steam button is
in its lower position (steam off). Always pull
the plug, not the cord. The cord should
never come in contact with hot objects or
with the hot sole plate.
• Never immerse the iron in water or other
liquids.
F Cleaning the anticalc valve
During ironing pauses, always place the
•
iron upright on its heel rest. Unplug it when
leaving the room, even if only for a short
time.
Never pull out the steam button (3) during
•
ironing.
• Keep the iron away from children.
Electric irons combine high temperatures 1) Unplug the iron and empty the water tank.
and hot steam that could lead to burns.
• Check the cord regularly for possible 2) Press the steam button so it is lifted.
damage.
If the appliance (including cord) shows any 3) Remove carefully (some water may now
•
defect, stop using it and take it to a Braun
Service Centre for repair.
4) Do not touch the anit-calc valve.
• Faulty or unqualified repair work may
cause accidents or injury to the user.
––––––––––––––––––––––––––––––––––––––––– 5) Immerse in vinegar (not vinegar essence)
6) Use a non-metallic brush until all openings
A Description
1 Spray nozzle 7) Rinse under running water.
2 Water tank opening
3 Steam button 8) Re-insert the steam button.
3a Steam regulator
4 Spray button 9) Press to check the steam on/off function.
5 Power shot button
6 Temperature selector
7 Temperature/auto-off* pilot light
B Before starting off
G Decalcifying / anticalc system
• This iron is designed for tap water. If you
have extremely hard water, we recommend
to use a mixture of 50% tap water and
50% distilled water. Fill the water tank to
«max» marking. Never use distilled water
exclusively. Do not add any additives
(e.g. starch).
1) Make sure the steam button is in its lower
• Keep the iron in the upright position and
connect it to the mains. Select the tem-
perature according to the ironing guide on 2) – 3) Fill water into the tank, connect to the
the heel rest of the iron or on the label in
your garments.
The temperature pilot light (7) goes off, 4) – 5) Wait until the pilot light turns off.
•
when the desired temperature is reached
(after approx. 1 minute).
6) – 7) Hold the iron over a sink, then press the
C Ironing
1 Steam on/off
For steam ironing, the temperature selector
(6) must be set within the red range.
8) Push back the steam button until it catches
Press the steam button (3) to start the
steam mode.
9) – 10) Fill water into the tank, connect to the
steam on steam off
With the steam button in its upper position, 11) – 13) When the pilot light goes off, press
turn the steam regulator (3a) to adjust the
steam quantity.
Preconditioning
(not with SI 6210 model)
Steam develops also horizontally at the
front area of the sole plate. This pre-
conditions the textiles by «pre-steaming»,
thus making ironing easier.
Be careful – steam comes out laterally.
H Trouble-shooting guide
2 Power shot
Prior to use, press the power shot button
(5) 3 to 4 times to activate it. Press the
power shot button in intervals of at least
5 seconds.
Power shot can be activated when dry
ironing. However, the temperature selector
has to be set in the range between «•••»
and «max». The power shot function can
also be used in the vertical position for
steaming hanging clothes.
3 Spray function
Press the spray button (4).
4 Dry ironing
Turn the steam mode off by pressing the
steam button (3) so that it catches in the
lower position.
5 Automatic shut-off*
(*available on SI 6245 model only)
Important: the auto shut-off feature is
mercury-free. The auto shut-off mechanism
causes a slight rattling noise during ironing.
This is normal and in no case indicates a
fault of the iron. The «auto-off» pilot light (7)
will flash when the automatic shut-off is
activated. This happens when the iron has
rested:
– horizontally on the soleplate for about
30 seconds or
– vertically on the heel rest (8) for about
15 minutes or
– when the iron has been lying on its side
for about 30 seconds.
To turn on the iron again just move it.
When the «auto-off» pilot light (7) stops
flashing the electrical power is on again.
Unplug the iron and press the steam on/off
button (3) so that it catches in its lower
position (steam off).
To prolong the life of the iron, empty the
water tank.
Store the cool iron in a dry place always
standing on its heel rest.
To clean the sole plate, use steel wool.
Then wipe the sole plate clean with a cloth.
Never use a scouring pad, vinegar nor
other chemicals. To clean the soft material
of handle and power shot and spray
buttons, use soapy water.
The iron's anticalc valve is located at the
lower end of the steam button (3). It has
to be decalcified regularly (e.g. when the
steam development is insufficient).
Proceed as follows:
leak from the sole plate).
or lemon juice until the lime becomes soft.
are clean.
Note: the iron must never be used without
the steam button.
When scale particles come out of the
steam vents or when the steam
development is insufficient even after
cleaning the anticalc valve, you should
clean the steam chamber as follows:
position.
mains and select the «•••» temperature
setting.
Unplug the iron.
steam button so it is lifted, carefully pull it
up, turn it and rest it in this position.
Caution: When the steam button is pulled
up, hot water and steam will come out from
the sole plate.
in the lower position.
mains and select the «•••» temperature
setting.
the power shot button 4 times to rinse the
iron. Disconnect the iron and wait for the
sole plate to cool off, then clean it as
described above in section E.
Note: the iron must never be used without
the steam button.
Problem Remedy
––––––––––––––––––––––––––––––––––––––
Drops Turn the steam regulator
coming out anti-clockwise to reduce
of the steam the steam or press the
vents steam button to turn the
steam off.
Take longer intervals
when pressing the power
shot button.
Select a higher tempera-
ture setting.
No steam Press the steam button
at all so that it is lifted.
Less steam Clean the anticalc valve
develops or no (see F).
steam at all
Calcium Decalcify the steam
particles chamber (see G).
coming through
the steam vents
––––––––––––––––––––––––––––––––––––––
Subject to change without notice.
This product conforms to the
EMC-Requirements as laid down
by the Council Directive 89/336/EEC
and to the Low Voltage Regulation
(73/23 EEC).