JVC KW-AVX708 Instructions Manual page 54

INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding
installation kits, consult JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are
used, there is a possibility that parts could become loose or damaged.
• When tightening screws or bolts be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear panel to maintain proper ventilation when installed.
1
Remove the audio system originally installed in the car, together with its mounting brackets.
Note: Be sure to keep all the screws and parts removed from your car for future use.
2
Attach the mounting brackets (removed from the car), to this unit (see below).
3
Connect the power cord and AV I/O cord
• See page 3 for the power cord connection.
• See page 4 for the AV I/O connection.
4
Install this unit using the screws removed in step 1 .
The following example is for installation in a Toyota car. For more details, consult your JVC car
audio dealer.
Mounting bracket removed from the car
從汽車拆卸的裝配架
Supplied screws
配備螺絲
Select the appropriate type fitting
to your audio system space.
選擇適合您的音響系統安裝空間的
型號。
Note : When installing the unit on the mounting bracket, make sure to use the
supplied screws (M5 x 8 mm). If longer screws are used, they could damage
the unit.
備注 : 安裝本機進裝配架時，請務必使用配備的螺絲（M5 x 8 mm）。若使用比較長的
螺絲，有關螺絲可能會損壞本機。
Required space for the monitor ejection
拆卸屏幕所需之空間
All manuals and user guides at all-guides.com
Mounting bracket removed from the car
從汽車拆卸的裝配架
安裝（裝設、固定在儀
下面的圖解表示了典型的安裝程序。但是在
果您有問題，或需要有關配套元件的資料，
• 如果您不能確定如何正確地安裝本機，應請
安裝本機之前
• 當裝上本機時，必須按照指示使用配備的螺
緊或損壞。
• 當鎖緊螺絲釘或螺栓時，切記不要壓擠到任
• 當安裝上后，切記不要阻擋到后面板的風扇
1
拆卸原本安裝在汽車內的音響系統，以及
備注：請務必保留所有從您汽車拆卸的螺
2
將（從汽車拆卸的）裝配架安上本機（請
3
連接電源線和音頻視頻輸入輸出電纜。
• 請參閱第 3 頁有關電源線連接。
• 請參閱第 4 頁有關音頻視頻輸入輸出連
4
使用在步驟 1 拆卸的螺絲安裝本機。
以下以豐田（Toyota）汽車安裝為例。請聯
Screws removed from the car in step 1
在步驟 1 從汽車拆卸的螺絲
Install the unit at an angle of less than 30˚
when in use (see below).
將本機安裝在少于 30˚ 的角度，您必須考慮
Supplied screws
配備螺絲
If necessary
若有必要，請
When ins
當安裝本機