1. Manuals
  2. Brands
  3. Ioline Manuals
  4. Cutter
  5. 350HF
  6. Quick start manual

Ioline 350HF Quick Start Manual

Hide thumbs Also See for 350HF:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
Ioline 300/350HF Systems
Quick Star t Guide
The Quick Start Guide is intended to help a new user of an Ioline
300/350HF System get setup and running quickly. Please note that
there are important notices, directions, troubleshooting, and other in-
formation in the electronic PDF 300/350HF User Guide and 301 Software
User Guide manuals available online in the 300/350HF support page
at ioline.com/support/300-350hf-support/.
required to view the User Guides and other electronic documents pro-
vided by Ioline.
The 300 and 350HF are powerful cutting machines. To avoid serious injury; keep fingers,
n
loose clothing and any objects that might get tangled in moving parts away from the
cutter during operation.
Before using, make sure that the cutter has 9-in of clearance in front and behind the
n
table to give the moving tray adequate space.
Do not try to repair the machine without factory authorization.
n
Never attempt to move the Carriage by hand when the power is on.
n
Be careful when moving or lifting the machine, it is heavy!
n
© 2019 Ioline Corporation. All rights reserved.
Adobe Acrobat
Important Cautions
September 10, 2019  FILE P/N: 107070 R8  PRINT P/N: 107077 R10
Reader® is

Advertisement

Table of Contents
loading

Related Manuals for Ioline 350HF

Summary of Contents for Ioline 350HF

  • Page 1 User Guides and other electronic documents pro- vided by Ioline. Important Cautions The 300 and 350HF are powerful cutting machines. To avoid serious injury; keep fingers, loose clothing and any objects that might get tangled in moving parts away from the cutter during operation.

  • Page 2: Visual Reference Guide

    Visual Reference Guide A. Left end cover H. Origin (starting point) B. Dust cover Thumb nuts (2) C. Carriage (design may Table (non-removable) vary) K. Leg (2) D. Adhesive sheet, mounted L. Power switch E. Right end cover M. Power connector Keypad N.

  • Page 3: Prepare The Production Area

    Assembly This Quick Start Guide shows how to assemble and set up the Ioline 300/350HF Systems. Consult the Acrobat PDF 300/350HF System ® User Guide, available online at ioline.com, for more detailed infor- mation about installation and operation. Adobe Acrobat viewer is ®...

  • Page 4: Step 1: Install The Software

    Restart the computer only if instructed. Connect the Ioline 301 Software key to a USB port on the PC (see figure below). Ioline recommends NOT using a USB hub for the key. Windows will likely show messages about driver installation when the key is inserted the first time.
  • Page 5 Choose an Adhesive Sheet (and backing material, if required) that are appropriate for the material you plan to cut. See Figure Below to identify proper sheet and backing types. More infor- mation about choosing Adhesive Sheets is also available in the 300/350HF System User Guide.)
  • Page 6 Ioline 300/350HF Quick Start Guide High Tack Scrim felt, leather, etching and stencil (HT) board. Order 107076 Medium Tack A general purpose sheet, use with most (MT) twills. Order 107295 Low Tack Heatseal-backed or thin and fragile (LT) materials. Order 107093 Ultra Low Tack Paper or paper-backed materials.

  • Page 7: Step 4: Install The Material And Tray

    Step 4: Install the material and tray Remove the striped cover from the Adhesive Sheet and care- Note fully apply fabric to the Tray. Smooth all bubbles out of the material (see figure below). Remember to remove material and cover DO NOT leave twill and other the adhesive sheet with the striped paper sheet when the cutter is not materials stuck on the adhesive...

  • Page 8: Need Help

    The are great accessories for the ing in the foot. 300 and 350HF that make your Insert the blade holder in the business even more productive. jaw then tighten the clamp.

This manual is also suitable for:

300hf

Table of Contents