Preparation For Use; Clock Set Up - Sylvania 6260VF Owner's Manual

3. Preparation for Use

Turn on the Unit for the First Time
1 1
Turn on the TV and set
it to channel 3.
• If channel 3 is already occupied for broad-
casting, see "RF Output Channel" section.
2
2
Remote Control TV Screen
POWER
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
or
3
3
CH 01
AUTO SET UP
Do you connect the cable from the cable box
or the satellite box to the VCR's ANT-IN jack?
Yes
Y es
Y es
Hit [MENU] to
exit
• Refer to "Hint for Cable Box or
Satellite Box" section on page 1. No
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memorized
in the unit by using [CHANNEL ].
• If "AUTO SET UP" appears on the TV screen
again, check the cable connections. Then, hit
[F.FWD g g ] once again.
Hint Hint
• Repeat these steps only if either there
was a power failure or if this unit has been
unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by using
the Number buttons on the remote
control.
Notes for using the Number but-
tons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number (for
example: 117, hit [1], [1], [7]).
• You must precede single-digit
channel numbers with a zero (for
example: 02, 03, 04 and so on).
To Preset the Channel Again
1) Hit [MENU] until the main menu appears.
2) Select "CHANNEL SET UP" by pressing
[PLAY B B ] or [STOP C C ]. Then, hit
[F.FWD g g ].
3) Select "AUTO SET UP" by pressing
[PLAY B B ] or [STOP C C ]. Then, hit
[F.FWD g g ]. After scanning, the tuner stops
on the lowest memorized channel.
To Change the On-Screen Language
1) Hit [MENU] until the main menu appears.
2) Select "LANGUAGE SELECT" by pressing
[PLAY B B ] or [STOP C C ]. Then, hit
[F.FWD g g ].
3) Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL" by pressing [PLAY B B ] or
[STOP C C ]. Then, hit [C.RESET/EXIT].
Hint Hint
• If you accidentally select Spanish or French
and need English: Hit [MENU] and choose
SELEC. IDIOMA, or SELECTION LANGUE.
Hit [F.FWD g g ] and select ENGLISH.
Finally, hit [C.RESET/EXIT].
To Add/Delete Channels
1 1
MENU
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
or
2
2
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
or
3
3
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
or
Select the channel to be
added or deleted.
4
4
MANUAL SET UP
CHANNEL 30 (CATV)
or
DELETE
Select "ADD" or "DELETE".
5 5
To exit the C.RESET
EXIT
menu.
- 3 -

Clock Set Up

1 1
MENU
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
• If the clock is not set, the
or
CLOCK SET screen
appears when you press
[MENU]. In this case, go
to step 2).
2
2
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
or
– – : – – – –
Select the current month.
3
3
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 – – – –
or HOUR MINUTE AM/PM
– – : – – – –
Select the current day.
4
4
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 2 0 0 5
or HOUR MINUTE AM/PM
– – : – – – –
Select the current year.
5 5
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
or HOUR MINUTE AM/PM
0 5 : – – – –
Select the current hour.
6
6
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
or
0 5 : 4 0 – –
Select the current minute.
7
7
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
or
0 5 : 4 0 P M AM
B PM
Select "AM" or "PM".
8 8
To exit the CLOCK SET
screen
Hint Hint
• To go back one step, hit [REW h h ] (during
steps 2 to 7).
• Your clock setting will be lost if either there
is a power failure or if this unit has been
unplugged for more than 30 seconds.
EN