Owner's Manual
Video Cassette Recorder
6260VF
1. Before Using Your VCR
Basic TV Connection
Antenna
Cable TV
Cable TV
Signal
Signal
or
(Back of TV)
Disconnect
4
Plug the AC power cords of the VCR and TV into the AC outlets.
Hint for Cable Box or Satellite Box
(Back of VCR)
(Cable box or
Antenna or
ANT
Satellite box)
IN
Cable TV
IN
OUT
signal
OUT
RF cable
(supplied)
(Back of TV)
Select this connection when you want to view
or record a scrambled channel. With this con-
nection, channels cannot be changed on the
unit. You can view or record ONLY the chan-
nels you have selected on the cable box or
the satellite box.
• While you are recording, only the recorded
channel can be viewed.
If you need additional operating assistance after
reading this owner's manual or to order replace-
ment accessories, please call
TOLL FREE : 1-800-968-3429
or visit our web site at
http://www.SylvaniaConsumerElectronics.com
Antenna
(Back of VCR)
or
ANT
2
IN
3
Connect
OUT
Connect
RF Cable
(supplied)
To select channels of the cable box or
satellite box
1) Turn on the unit by hitting [POWER], then
E
hit [VCR/TV].The "POWER" and the
"VCR/TV" indicator on the front panel will
appear, then press [CHANNEL
select channel 3 or 4 (the same channel as
the output channel of the cable box or
satellite box).
• If you use the channel 4, you need to
change the unit's RF output to channel 4.
Refer to "RF Output Channel".
2) At the TV, select channel 3 or 4 (the same
channel as you have selected at step 1).
3) On the cable box or satellite box, select the
channel you want to view or record.
RF Output Channel
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Hit [PLAY B B ] once.
4) After a few seconds, hold [PLAY B B ] on the unit for 3 seconds.
• The RF output channel will change to channel 4 from channel 3 and you
will see a playback picture.
• When a picture does not appear on the TV screen, repeat step 4).
5) Hit [STOP C C ] to stop playback.
Stereo TV Connection
You can use the AUDIO OUT jacks
and VIDEO OUT jack on the back of
the VCR if your TV has Audio/Video
Input jacks. In this case, you need to
(Back of TV)
set the TV to external Line Input
Mode. Please refer to your TV's
owner's manual.
Front & Rear Terminals
AUDIO OUT jacks
Connect the audio cables here through to the audio
input jacks of a camcorder, another VCR, a stereo
amplifier, a stereo amplifier or an audio system.
VIDEO OUT jack
Connect the video cable here through the video
input jack of a camcorder, another VCR or a TV.
] to
POWER
CHANNEL
VIDEO
L - AUDIO - R
Supplied Accessory
• Remote control
• RF cable
(NA376UD) with
(WPZ0901TM002)
two AA batteries
- 1 -
VIDEO
AUDIO IN
IN
L
Audio/Video Cables
(not supplied)
VIDEO
AUDIO OUT
OUT
L
R
(Back of TV)
AUDIO IN jacks
Connect the audio cables coming from the
audio output jacks of a camcorder, another
VCR or an audio source here.
ANT
ANT IN jack
AUDIO
IN
L
Connect your antenna or cable box here.
ANT
AUDIO
IN
OUT
IN
L
OUT
IN
R
R
ANT OUT jack
VIDEO
OUT
VIDEO
OUT
OUT
IN
Connect the supplied RF cable to the
antenna input jack on your TV.
OUT
IN
VIDEO IN jack
Connect the video cable coming from the
video output jack of a camcorder, another
VCR or an audio-visual source (laser disc
MEN
player, video disc player, etc.) here.
TAPE IN
Installing the Batteries for
the Remote Control
• Owner's manual
Install two AA batteries
(1VMN20688)
(supplied) matching the
polarity indicated on
the bottom of the
remote control.
1VMN20688 / HJ411UD #####
Hint
Hint
• The RF output channel may
not change when you adjust
tracking during playback. In
this case, stop the playback,
and start the playback again.
After that, hold [PLAY B B ] on
the VCR for 3 seconds again.
R
ANT
AUDIO
IN
L
OUT
IN
R
OUT
VIDEO
OUT
IN
ANT
IN
OUT
(Back of VCR)
Printed in China