Channel Set Up - Sylvania 6313CG Owner's Manual

CHANNEL SET UP

Make sure ...
•
The unit must be turned on.
AUTO CHANNEL PROGRAMMING
As the initial setting, this unit has memorized all
channels, including the ones not available in your
area. This feature automatically puts only available
channels into the memory.
1
Select "CHANNEL SET UP"
Press [MENU].
Use [PLAY/ K K ] or [STOP/ L L ] to
point to "CHANNEL SET UP",
then press [F.FWD/ B B ].
2
Begin channel scanning
Use [PLAY/ K K ] or [STOP/ L L ] to
point to "AUTO CH PROGRAM-
MING", then press [F.FWD/ B B ].
The tuner scans and memorizes all
the active channels in your area.
3
After scanning
The tuner stops on the lowest memorized channel.
NOTES:
•
If there is no TV signal input, "NO TV SIGNALS"
will appear on the display after the completion of
channel scanning.
•
The unit may recognize TV channels to be CATV
channels if reception condition is poor. In this case,
check the antenna connection and try "AUTO CH
PROGRAMMING" again when reception condi-
tions are better.
•
Auto channel programming is NOT necessary
when connected to a cable box or satellite box.
Just select the channel for the cable box or satel-
lite input (ex. CH3 or CH4) on the unit, then
select your desired channel on the cable box or
satellite box.
ADDING/DELETING CHANNELS
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you can
add the deleted channel into the memory again.)
1
Select "CHANNEL SET UP"
Press [MENU].
Use [PLAY/ K K ] or [STOP/ L L ] to
point to "CHANNEL SET UP",
then press [F.FWD/ B B ].
2
Use [PLAY/ K K ] or [STOP/ L L ] to
point to "ADD/DELETE CH", then
press [F.FWD/ B B ].
3
Use [PLAY/ K K ] or [STOP/ L L ] or
the Number buttons until your
desired channel number appears.
(You can also use
– M E N U –
[CHANNEL K K / L L ] to enter it.)
TIMER PROGRAMMING
•
PICTURE CONTROL You must precede single-digit
SETTING CLOCK
B CHANNEL SET UP
channel numbers with a zero (Example: 02 ... 09).
USER'S SET UP
V-CHIP SET UP
•
LANGUAGE [ENGLISH] When selecting cable channels which are higher
CAPTION [OFF]
ZERO RETURN
than 99, press [+100] first, then enter the last two
TIME SEARCH
digits. (Example: to select channel 125, first press
[+100] then press [2] and [5].)
– CHANNEL SET UP –
4
ADD / DELETE CH (CATV)
B AUTO CH PROGRAMMING
Use [REW/s s ] or [F.FWD/B B ]. The channel number
changes to light red. The channel is deleted from
memory.
•
To delete another channel, repeat steps 3 to 4.
•
If you use [REW/s s ] or [F.FWD/ B B ] again, the
channel is memorized again.
5
Press [MENU] to returns to TV mode.
NOTE:
•
To confirm that channel(s) has been deleted or
added, use [CHANNEL K K / L L ].
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
B CHANNEL SET UP
USER'S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
- 11 -
Select "ADD/DELETE CH"
Enter the desired channel number
Delete (or add) it from (or into) memory
Added channel: Light blue
Deleted channel: Light red
Exit the channel setup mode
– CHANNEL SET UP –
B ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
08
ADD / DELETE
EN