Table of Contents
Advertisement
OTR (One Touch Recording)
This function enables you to set a recording length
simply by hitting
[REC/OTR] on the unit.
Make sure ...
•
The unit must be turned on.
•
Insert a cassette tape with its erase-prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
NOTES:
•
You cannot start OTR with the remote control.
•
Recording starts immediately when [REC/OTR]
is hit.
•
When [REC/OTR] is hit 18 times, the unit returns
to the Normal Recording mode.
•
To stop the OTR operation, hit [STOP/EJECT
on the unit or on the remote control.
•
To show the remaining time, hit [DISPLAY] on
the remote control so that "OTR" appears on the
TV screen. (It will show up momentarily then dis-
appear.)
•
Recording stops when the display shows 0:00.
•
Please note that in the SLP mode maximum
recording time, assuming the tape is started at the
beginning, is 8 hours using T-160 (or 6 hours
using T-120).
•
If the tape runs out before the end time, the unit
will switch to the stop mode immediately, ejects
the tape and turns itself off.
•
Even if [POWER] is hit during OTR, the unit
continues recording.
1
Select the channel to be recorded
Press the Number buttons or [CHANNEL K/L].
NOTE:
•
If the unit is connected to a cable box or satellite
box, the unit must be on CH3 or CH4, then the
channel to be recorded is selected on the cable box
or satellite box.
2
Select the tape speed
Hit [SPEED] to select the desired tape speed
(SP/SLP).
3
Begin OTR
Hit [REC/OTR] on the unit as
many times as needed. The record-
ing length will be determined by
the number of times you hit
[REC/OTR]. Each time it is hit, the recording time
will be increased by 30 minutes up to 8 hours.
Time(s)
2 times
3 times
17 times
COPYING A VIDEO CASSETTE
You can make copies of video tapes made by friends
or relatives for your enjoyment.
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
]
Connect your unit and a source (playing) VCR using
P P N N
the following diagram.
[This unit]
Audio/Video cable
(not supplied)
1)Insert a pre-recorded video cassette into the source
VCR or camcorder.
2)Insert a blank video cassette or one you want to
record over, into the unit's cassette compartment.
3)Hit [SPEED] on remote control for the unit to
select the desired recording speed (SP/SLP).
4)Press [CHANNEL X X /Y Y ] on the unit until "AUX"
appears on the screen.
5)Hit [REC/OTR] on the unit.
6)Begin playback of the tape in the source VCR or
camcorder.
NOTE:
OTR (2 : 30)
•
SP
7)To stop copying, hit [STOP/EJECT
unit, then stop the tape on the source VCR or cam-
corder.
- 22 -
Display
1 time
(normal recording)
0:30
1:00
8:00
(Requires a VCR or camcorder)
VIDEO
For best results during copying, use the front
panel controls whenever possible. The remote
control might affect the source VCR's playback
operation.
Recording length
30 minutes
60 minutes
480 minutes
AUDIO
POWER
VOLUME
C
L
K
L
K
[Ex: Source
VCR or camcorder]
AUDIO
OUT
IN
VIDEO
] on the
P P N N
C A
E
B
D
EN
Advertisement
Table of Contents
