Hints For Timer Recording - Sylvania SSD800 Owner's Manual

4) Set the start time
First, press the PLAY button or the STOP
button for the hour. Then, press the
F.FWD button. Next, press the PLAY
button or the STOP button for the minute. Then, press the
F.FWD button. And then, press the PLAY button or the
STOP button for AM or PM. Then, press the F.FWD button.
5) Set the end time
Follow the same instructions as
"Set the start time" to set
the end time.
6) Set the channel number
Press the PLAY button or the STOP
button repeatedly for the desired channel
number. Then, press the F.FWD button.
If you connected the DVD/VCR to a cable box or satellite box
as in "DVD/VCR TO TV CONNECTION" on page 14, set the
DVD/VCR to channel 3 or 4 i.e. the same channel as the CH3
or CH4 switch on the back of the DVD/VCR. Then, select the
channel you want to record with the cable box or satellite box.
Leave the cable box or satellite box on for timer recording.
7) Set the tape speed
Press the PLAY button or the STOP
button repeatedly for the desired tape
speed. Then, press the F.FWD button.
5
To set another program, repeat step [4]. To exit
from the set up screen, press the
CLEAR/C.RESET button (You only exit from the
set up screen. the information you entered for
the timer recording will not be cleared).
6
When you finish programming, press the
TIMER SET button to activate the timer.
¡
As the TIMER SET light comes on the VCR
becomes STANDBY status, and switches to DVD
OUTPUT mode automatically.
¡ When DVD sits idle for more than thirty-five min-
utes, the DVD power will be turned off automatical-
ly. If you press the TIMER SET button under such
condition, the VCR power will be turned off and
become STANDBY status.
TO CLEAR A PROGRAM
Follow the steps from 2 to 3. Select the program num-
ber you want to clear, and then press the REW button.
HINTS FOR TIMER
RECORDING
¡ If there is a power failure or the VCR is unplugged
for more than 30 seconds, the clock setting and all
timer settings will be lost.
¡
If a tape ends during TIMER RECORDING, the
VCR will stop, eject the tape, and switch to the DVD
mode automatically as the TIMER SET light blinks.
(If the DVD power is off, the VCR will become
STANDBY status).
¡
If a tape is not in the VCR or does not have a safety tab,
ONE TIME PROGRAM
the TIMER SET light flashes and timer recording will
PROGRAM NUMBER 4
DATE
05 /13 MON
not operate. Please insert a recordable tape.
START TIME
- - : - - - -
END TIME - - : - - - -
¡
When all timer recordings are finished, the TIMER
CHANNEL - -
REC SPEED - -
SET light will flash. To use the VCR again as usual,
press the TIMER SET button to disable the flashing
TIMER SET light, then press the VCR/TV button to
select the VCR position. The VCR/TV light will
appear. Press the VCR button to choose VCR or DVD
mode, then continue with the other features as
ONE TIME PROGRAM
described in this manual.
PROGRAM NUMBER 4
DATE
05 /13 MON ¡
When timer recordings are set, the TIMER SET light
START TIME
07: 30 PM
END TIME
- - : - - - -
will come on. To use the VCR as usual until the time
CHANNEL
- -
REC SPEED
- -
for the recording, press the TIMER SET button so that
the TIMER SET light disappears. Press the VCR/TV
button to choose the VCR position. The VCR/TV light
ONE TIME PROGRAM
will come on. Press the VCR button to choose VCR or
PROGRAM NUMBER 4
DATE
05 /13 MON
DVD modes, then continue with the other features as
START TIME
07: 30 PM
END TIME
08: 30 PM
described in this manual.
CHANNEL
- -
REC SPEED
- -
If you want to use the DVD player during
a VCR timer recording or while the TIMER
SET light is on or flashes.
¡
You can use the DVD player while the TIMER SET
light is on or flashes, or during a timer recording. Press
the POWER button to turn on the VCR. Press the
VCR/TV button to choose VCR position. Press the
DVD button on the remote control to choose DVD
ONE TIME PROGRAM
PROGRAM NUMBER 4 mode, then continue with the other DVD features as
DATE 05 /13 MON
START TIME 07: 30 PM
described in this manual. You don't have to set the
END TIME
08: 30 PM
CHANNEL
16
TIMER off to use the DVD.
REC SPEED SP
SP
SLP
TO STOP AN AUTOMATIC TIMER PRO-
GRAM ALREADY STARTED
Press the STOP/EJECT or the TIMER SET button on
the DVD /VCR.
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
1
2
3
4
¡
The details of the selected program appears on the
TV screen.
VCR
¡
Go to the digit you want to change by pressing the
F.FWD or the REW button. Then, enter correct num-
bers by pressing the PLAY or the STOP button.
¡
You may cancel the entire program by pressing the
REW button while the program number flashes.
5
6
– 21 –
Turn the power on by pressing the POWER
button. (If the VCR is in TIMER STANDBY
status, press the TIMER SET button instead
of the POWER button.)
Select main menu by pressing the MENU
button.
Select "TIMER PROGRAMMING" by press-
ing the PLAY or the STOP button. Then, the
F.FWD button.
Select the program number which you want
to check by pressing the PLAY or the STOP
button.
Press the CLEAR/C.RESET button to exit.
Press the TIMER SET button to return to
timer stand-by mode.
EN
1L25